Bedienungsanleitung Skoda Rapid - 2013 (Seite 183 von 218) (Englisch)

678345

183

Zoom out

Zoom in

Vorherige Seite

1/218

Nächste Seite

Breakdown kit

Fig. 152 Components of the breakdown kit

First read and observe the introductory information and safety warn-

ings on page 180.

The kit is located in a box under the floor covering in the luggage compartment.

Components of the breakdown kit

Valve remover

Sticker with speed designation “max. 80 km/h”/“max. 50 mph”

Inflation hose with plug

Air compressor

Tyre inflation hose

Tyre inflation pressure indicator

Air release valve

ON and OFF switch

12 volt cable connector

Tyre inflator bottle with sealing agent

Replacement valve core

The valve remover

has a slot at its lower end which fits into the valve core.

This is the only way in which you can remove and re-install the valve core from

the tyre valve. The same also applies to the replacement valve core





Preparations for using the breakdown kit

First read and observe the introductory information and safety warn-

ings on page 180.

The following preparatory work must be carried out before using the breakdown

kit.

›

Park the vehicle as far away as possible from the flow of traffic. Park on as flat

and firm a surface as possible.

›

If you are in flowing traffic, switch on the hazard warning light system and set

up the warning triangle at the prescribed distance! The national legal require-

ments must be observed.

›

Let all of the occupants get out. While changing a tyre, the occupants of the

vehicle should not stand on the road (instead they should remain behind a crash

barrier).

›

Switch off the engine and move the gearshift lever into Neutral or move the se-

lector lever on the automatic gearbox into position P.

›

Firmly apply the handbrake.

›

Check that you can carry out the repairs with the breakdown kit » page 180.

›

If a trailer is connected, uncouple it.

›

Remove the breakdown kit from the boot.

›

Stick the sticker

» Fig. 152 on page 181 on the dash panel in view of the driv-

er.

›

Do not remove the foreign body, e.g. screw or nail, from the tyre.

›

Unscrew the valve cap.

›

Use the valve remover

to unscrew the valve core and place it on a clean sur-

face (rag, paper, etc.).



Sealing and inflating the tyre

First read and observe the introductory information and safety warn-

ings on page 180.

Sealing

›

Forcefully shake the tyre inflator bottle

» Fig. 152 on page 181 several times.

›

Firmly screw the inflation hose

onto the tyre inflator bottle

in a clockwise

direction. The film on the cap is pierced automatically.

›

Remove the plug from the inflation hose

and plug the open end fully onto

the tyre valve.

›

Hold the bottle

with the bottom facing upwards and fill all of the sealing

agent from the tyre inflator bottle into the tyre.





181

Emergency equipment and self-help

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skoda Rapid - 2013 Seite 183

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skoda Rapid - 2013

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info