Bedienungsanleitung Snom M300 (Seite 77 von 84) (Englisch)

621561

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

v1.06

Admin and Installation Guide M700, M300 Description of Settings

Multicell

Please note that all base stations in a multicell setup must have the same rmware. We recommend

that you update all base stations to the latest rmware and reset them before beginning the multicell

installation.

• Reset secondary base stations to defaults, and, after the reset, change their DHCP Options

"Plug-n-Play" setting on the Network page to "Disabled".

• Use only the designated primary (master) base station to enter all data, i.e., set up the SIP

server(s), creating extensions/user accounts, register handsets, etc.

• Note: Entering a time server on the Time settings page of the primary base station's web

interface is mandatory for multicell installations!

Setting Description

Settings for this unit

Multicell system Select "Enabled" or "Disabled" from the drop-down list.

Default: Disabled.

System chain ID All base stations in a multicell system must have the same system chain ID.

• Note 1: The chain ID is used as a SIP account, i.e., extension 512, to

identify dierent DECT chains in the same network. This means that you

cannot assign extension 512 to handsets or use it for calls. It is possible

to assign a dierent chain ID, but by provisioning only (valid input: up to

5 digits).

• Note 2: There can be several multi-cell systems in the network. Up to 24

levels of base station chains are permitted.

Default: 512

Synchronization time (s) Species the period in seconds when base stations in a multicell system

synchronize with each other. If no keepalive packets are received within this

period, the base station will be treated as unreachable in the multicell system.

Default: 60 seconds

Data Sync Select multicast or peer-to-peer from the drop-down menu. Multicast

uses UDP. The multicast port (range 49200-49999) and IP address (range

224.1.0.0-225.1.0.0) are calculated from the chain ID.

Default: Multicast

Primary data sync IP IP address of base station data sync sourse, i.e., the base station handling the

data synchronization.

• When the data sync setting is multicast, this setting is disabled; the IP is

selected automatically.

• If data sync setting is peer-to-peer, the source must be dened. The

default value is 0.0.0.0.

Multicell debug 224.1.0.0-225.1.0.0)

• None: Debug disabled.

• Data sync: Writes header information for all packets received and sent,

to be used to debug any special issues.

Note: This option should only be enabled for short periods of

time when debugging is needed, as it generates a lot of syslog

signaling.

• Auto tree: Writes states and data related to the auto tree conguration.

• Both: "Data sync" and "auto tree" are both enabled.

Note: This option must only be used for debugging and not

enabled on a normal running system.

Default: None

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snom M300 Seite 77

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Snom M300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info