Bedienungsanleitung Snom M300 (Seite 78 von 84) (Englisch)

621561

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

v1.06

Admin and Installation Guide M700, M300 Description of Settings

Setting Description

DECT system settings

RFPI system The RFPI of the base station is entered automatically.

Auto congure DECT sync

source tree

Allows the multicell system to automatically synchronize the multicell chain/

tree. This setting must be enabled to allow a secondary base station to take

over the primary base station function if the original base station becomes

disabled.

Default: Enabled

Allow multi primary This feature allows two or more primaries in the same system and is used for

multilocation setups. The primaries are unsynchronized, and handover is not

possible. The setting Auto congure DECT sync source tree must be enabled.

Default: Disabled

Auto create multi primary Available when the setting Allow multi primary is enabled. This setting

enables the multicell system to generate a second cell when a base station

goes o-line and radio connection between parts of the system is lost. After

reconnecting the faulty base station, the system must be rebooted.

Default: Disabled

Base station settings

Number of SIP accounts

before distribution load

The maximum number of handsets that are permitted to perform location

registration on a specic base station before the load is distributed to other

base stations. The parameter can be used to optimize handset distribution

among visible base stations.

Note: In a multi-cell setup, a maximum of 8 simultaneous

calls can be routed through each base station.

Permitted input: Positive integers (e.g., 8)

SIP server support for

multiple registrations per

account

Select option from drop-down menu.

Disabled: (For servers that do not support moving SIP registrations from

base station to base station when handset roams.) The SIP registration of

a handset remains on the original base station when the handset roams to

another base station. The handset does not SIP-register on the second base

station.

Enabled: When a handset roams to another base station, the SIP registration

of the handset on the original base station is deregistered, and the handset

SIP-registers on the second base station.

Default: Disabled

System combination (number

of base stations/repeaters

per base station)

Three settings are available.

Note: The conguration must be set at the time the multicell

system is congurated. It cannot be modied:

50/3: 50 base stations and 3 repeaters

127/1: 127 base stations and 1 repeater

254/0: 254 base stations and 0 repeater

Base Station Group

ID Base station identity in the chained network. Automatically assigned

consecutively when new base stations are added to the chain. With checkbox

for selection for removal from chain.

Permitted output: Positive integers.

RPN The Radio Fixed Part Number is an 8-bit DECT cell identity allocated by the

installer. The allocated RPN within the SME must be geographically unique.

Permitted output: 0 to 255 (DEC) or 0x00 to 0xFF (HEX)

Version Current rmware version on base station.

Permitted output: Positive integers with dot (e.g, 355.21).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snom M300 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Snom M300

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info