Bedienungsanleitung Solac SW8231 (Seite 12 von 32) (Englisch, Französisch, Italienisch, Portugiesisch, Spanisch)

799214

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Winding the bobbin

- 1. Put a spool of thread on spool pin. (Fig.20)

- 2. Guide the thread through the bobbin winder tension disk on the

upper side of the machine. (Fig.21)

- 3. Put the bobbin on the bobbin winder pin, wind thread clockwise

around bobbin several times. (Fig. 22)

- 4. Push bobbin to the left. (Fig.23)

- 5. Switch on the machine to start winding. (Fig.24)

- 󰀨

thread you wanted had winded on bobbin.

- 󰀨

and cut the thread. (Fig.25)

Caution

- During bobbin winding, no thread on the needle/take up lever is al-

󰀨

- Before bobbin winding, raise the presser foot.

Adjusting stitching

- 1. As shown in the picture A, normal stitching shall have top and bot-

tom threading evenly, neither over tight nor loose.

- 2. If the bottom threading looks like a straight line (Fig.B), which indi-

cates the top thread is too loose. Please turn upper thread tension dial

to direction with bigger number to increase pressure until the stitching

return to norma.

- 3. If the top thread looks like straight line (Fig.C), which indicates an

over-tight top thread. Please turn the upper thread tension dial to the

direction with smaller number to reduce pressure until the stitching

back to normal.

Other functions

Overlocked

󰀨

- We must select an overlock or overlock stitch, 5 or 6 leaving the width

and length values that come by default. (depending on the machine

they will be one or the other)

- Advancing slowly, the fabric that we have left, while the needle is



󰀨

Pre-riveted drilling

- It consists of moving the needle without thread front and back to pierce

the fabric and thus be able to put a brooch or a rivet.

- If you want a bigger hole you should change the needle to a thicker

one.

Applicable cloth for sewing

Cloth

Sewing

presentation

Cotton /

Linen

Silk /

Wool

Polyester Elastic

-

cation

Regular    

Thick    

Thin    

Hard    

Soft    

󰀨

• 

• 󰀩

• 

Note:



• 

• Thick (fabric): two layers of the fabric thickness >0.8mm

• 





• If the cloth, which size is “100mmx30mm”, is extending to or

over 106 mm under 0.5Kg tension force, then the cloth is de-





4. Soft fabric: such as towel, duster, etc.



- 󰀨󰀨

- 󰀨

- Unplug the appliance from the mains.

- Put the cable back in the cable housing.

- Clean the appliance.

Carry handle/s:

- This appliance has a handle on the upper part of the body, which facili-

tates comfortable transportation.

Safety thermal protector:

- The appliance has a safety device, which protects the appliance from

overheating.

- 󰀨

disconnect it from the mains supply, and wait for approximately 15

minutes before reconnecting. If the machine does not start again seek

authorised technical assistance.

CLEANING

- Disconnect the appliance from the mains and allow it to cool before

undertaking any cleaning task.

- Clean the equipment with a damp cloth with a few drops of washing-up

liquid and then dry.

- Do not use solvents, or products with an acid or base pH such as

bleach, or abrasive products, for cleaning the appliance.

- Do not let water or any other liquid get into the air vents to avoid dam-

age to the inner parts of the appliance.

- Never submerge the appliance in water or any other liquid or place it

under running water.

Supplies

- Supplies can be acquired from distributors and authorised establish-



- Only the following type of supplies must be used with the appliance.

- Lamp type: E14, Max: 15 W

- These supplies are available in specialist shops.

Solac SW8231 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info