474213

Sommer Duo 650SL Seite 22

22
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
Operation and Handling
21
Interim stop
If an interim stop occurs due to the operation of a push-button or the
manual remote control, the drive unit stops immediately. The next command
given sends the drive in the opposite direction. See 'Pulse Sequence of
Door Movement' section.
Safety stop 1
(automatic force cut-off)
When the automatic force cut-off is activated, the drive stops or reverses.
When the next command is given, the drive moves in the opposite direction.
See 'Pulse Sequence of Door Movement' section.
- Safety stop when door closes - door reverses
- Safety stop when door opens - door stops.
Safety stop 2
(automatic force cut-off)
When the safety input is tripped (e.g. someone crosses light barrier), the
drive stops, reverses or opens, depending on the given DIP switch setting:
- DIP switch 1 + 3
See 'Obstacle Recognition' section for given drive type.
When the next command is given, the drive moves in the opposite direction.
See 'Pulse Sequence of Door Movement' section.
Default settings:
- safety input tripped when door closes:
door reverses
- safety input tripped when door opens:
no response (door opens).
Overload protection
If the drive mechanism is subjected to excessive strain when opening or
closing the door, this is recognised by the control unit which then stops the
drive mechanism. After approx. 20 seconds or a control unit reset, the
control unit deactivates the overload protection.
The drive mechanism can now recommence normal operation.
Operation following a power failure
The force values remain saved even during a power failure. The first
movement of the unit following a power cut is always door OPEN.
Radio remote control receiver
Homelink compatible!
If your vehicle is equipped with a Homelink system (version 7),
you can reach our drive/radio receiver at 868.6 MHz. With holder
Homelink systems, you must use a different frequency (40.685 or
434.42 MHz). For more information, please visit:
"http://www.eurohomelink.com"
• To ensure safe operation, local safety regulations relevant to the
equipment concerned must be observed! Information regarding this can
be obtained from electricity suppliers, the VDE and employers' liability
insurance associations.
• The operator of this radio-controlled equipment is in no way protected
from interference from other telecommunications systems and facilities
(e.g. other radio-controlled equipment that is licensed to operate at the
same frequency range).
• Try replacing the batteries should reception problems be encountered.
Description of display and
push-buttons
1 Setting button
Puts radio receiver in a given operating mode:
self-learn, delete and normal
2 Internal aerial
3 LED
Display which channel has been selected.
3.1 LED channel 1
3.2 LED channel 2
4 Connection for external aerial (6)
If the radio range of the internal aerial is not sufficient, you have
the option to connect an external aerial.
5 Manual remote control button
6 External aerial
Teaching in manual remote control
• Press setting button (1)
- Press 1x for channel 1; LED (3.1) lights up
- Press 2x for channel 2; LED (3.2) lights up
- If no radio code is transmitted within 10 seconds, the receiver
switches back to normal operating mode.
- Interrupting setting mode: press setting button (1) as often as
required to put out all LEDs
• Press and hold desired hand-held transmitter key until the LED (3.1 /
3.2) is off - depending on the selected channel.
• The LED is off - the programming process is completed.
The hand-held transmitter has transmitted the radio code to the radio
receiver.
Teaching in further manual remote controls. Repeat above steps.
Max. 112 memory slots are available per radio receiver.
Deleting manual remote control
button from radio receiver
If a user of a multi-user garage facility moves house and wants to take his
manual remote control with him, then all the codes of the given user's
manual remote control have to be deleted from the radio receiver.
For security reasons, each manual remote control button and/or
combination of buttons should be deleted!
• Press setting button (1) and keep depressed for 5 seconds until an
LED starts to flash (any LED).
• Release setting button (1) - radio receiver is in delete mode.
• Press push-button on the manual remote control, the one whose
code is required to be deleted on the radio receiver - LED goes out -
deletion process complete.
Repeat procedure for all push-buttons and combination of buttons.
5
T2
2
4
6
3.1
3.2
1
7
8
4
5
6
5
2
6
4
3.1
3.2
1
… 22 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

sommer-duo-650sl

Suche zurücksetzen

  • Was muss ich machen um ddn Code der Fernbedienung zu ändern? Eingereicht am 29-5-2023 14:02

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Sommer Duo 650SL wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Sommer Duo 650SL

Sommer Duo 650SL Bedienungsanleitung - Deutsch - 37 seiten

Sommer Duo 650SL Bedienungsanleitung - Holländisch - 40 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info