Bedienungsanleitung Spektrum DX5e (Seite 12 von 19) (Englisch)

726845

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

SPEKTRUM DX5e • RADIO USER’S GUIDE

ENDEFRIT

FRANCE RF SETTING

TO SET FRANCE MODE:

Hold the trainer switch and push and hold the Aileron

trim button to the left. Turn on the transmitter. A series of

descending tones should be heard. Release switches.

TO SET STANDARD MODE:

Hold the trainer switch and push and hold the Aileron trim

button to the right. Turn on the transmitter. A series of

ascending tones should be heard. Release switches.

RECEIVER POWER SYSTEM

REQUIREMENTS

With all radio installations, it is vital the onboard power

system provides adequate power without interruption to the

receiver even when the system is fully loaded (servos at

maximum ﬂight loads). This becomes especially critical with

giant-scale models that utilize multiple high-torque/ high-

current servos. Inadequate power systems that are unable

to provide the necessary minimum voltage to the receiver

during ﬂight loads have become the number-one cause of

in-ﬂight failures. Some of the power system components

that affect the ability to properly deliver adequate power

include: the selected receiver battery pack (number of cells,

capacity, cell type, state of charge), switch harness, battery

leads, regulator (if used) and, unless it’s a regulator, power

bus (if used).

While a Spektrum receiver’s minimum operational voltage

is 3.5 volts, it is highly recommended the system be tested

per the guidelines below to a minimum acceptable voltage of

4.8 volts during ground testing. This will provide head room

to compensate for battery discharging or if the actual ﬂight

loads are greater than the ground test loads.

RECOMMENDED POWER SYSTEM

GUIDELINES

1. When setting up large or complex aircraft with multiple

high-torque servos, it’s highly recommended that a

current and voltmeter (Hangar 9 HAN172) be used. Plug

the voltmeter in an open channel port in the receiver

and, with the system on, load the control surfaces

(apply pressure with your hand) while monitoring the

voltage at the receiver. The voltage should remain above

4.8 volts even when all servos are heavily loaded.

2. With the current meter in line with the receiver battery

lead, load the control surfaces (apply pressure

with your hand) while monitoring the current. The

maximum continuous recommended current for a

single heavy-duty servo/battery lead is three amps

while short-duration current spikes of up to ﬁve amps

are acceptable. Consequently, if your system draws

more than three amps continuous or ﬁve amps for short

durations, a single battery pack with a single switch

harness plugged into the receiver for power will be

inadequate. It will be necessary to use multiple packs

with multiple switches and multiple leads plugged into

the receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX5e Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX5e

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info