Bedienungsanleitung Spektrum DX8 (Seite 20 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite



Electric RPM Sensor

The optional electric RPM sensor is designed to be used with any brushless

motor. The sensor has two leads to attach to any two of the three motor wires.

This is typically done by soldering.

Installation

To install the electric RPM sensor using servo tape, attach the sensor in

a convenient place that allows the leads to reach the motor wires and the

TM1000 telemetry unit.

Solder the two sensor wires to any two motor leads.

Plug the sensor lead into the RPM port on the TM1000 telemetry module.

Testing

Turn the transmitter and receiver on and scroll to the RPM telemetry screen.

Run the motor and the RPM should register on the screen.

The RED LED on the TM1000 indicates the sensor is picking up properly.

 It is necessary to program a matching pole count in the telemetry

RPM screen to have accurate reading on screen. The motor’s pole count is

normally in the motor manufacturer’s instructions or on the manufacturer’s

website.



The Frame Rate function allows the selection of 11ms or 22ms frame rate. When

a 11ms frame rate receiver is used, the transmitter defaults to 11ms frame rate.

This fast frame rate is not compatable with some types of analog servos and the

Frame Rate screen allows the selection of a 22ms frame rate when a high frame

rate receiver is being used with analog servos.



Press and hold the roller while turning on the the transmitter. When system setup

appears on screen relese the roller. The DX8 is now in System Setup mode.

Rotate the roller to highlight Frame Rate then press.

The following screen appears:

Rotate the roller to highlight the frame rate then press. Now rotate the roller to

select 11ms or 22 ms frame rate.



The DX8 features a programmable trainer function with three trainer modes. The

transmitter assigns the trainer function to the trainer button. The function activates

when the switch is depressed and one of the three trainer modes is selected. The

three trainer Modes include:



In Inhibit you can use the transmitter as a slave only. However, the slave

transmitter must have the same programming as the master (e.g., servo

reversing, travel adjust, sub-trim, trims).



With Programmable Master you can program the transmitter to transfer any or

all channels when you activate the trainer switch. This is ideal for beginners

so the student learns control of individual channels (aileron only for example)

while the trainer maintains control of all other channels.

Note: When Programmable Master is selected for the master transmitter,

all settings for the slave transmitter (i.e. Servo reversing, wing type, Sub

trim, Travel Adjust, Mixing, etc.) must match the master’s transmitter

programming. If two DX8’s are being used simply copy and transfer the

model memory using the SD card from the master’s model to the slave.

The slave transmitter is then programmed to inhibit in the trainer screen.



When Pilot Link Master is selected the slave transmitter has control of the

stick function only (aileron, elevator rudder and throttle) while the master

maintains control of all other channels and functions including D/R and

switch positions. This is ideal for complex models as the master maintains

control of all secondary functions and controls all other channels.



Use Slave mode when ﬂying with the DX8 as a slave when the master

radio has activated its Pilot Link. In this case, there is no need to match

programming between the slave and master transmitter.



Use the System Setting screen to establish the overall transmitter setting that will

apply to ALL model memories. These settings include: User Name, Contrast,

Mode, Region and Language. If you select Mode One, then Mode One will be

selected for all 30 model memories. Note: Even when models are imported from

an SD card the system settings in the transmitter will remain.



Press and hold the roller while turning on the transmitter. When System Setup

appears on the screen, release the roller. The DX8 is now in System Setup Mode.

Highlight System Settings then press. The following screen appears:

Highlight the function you wish to change then press the roller to select.

User Name

User Name allows the identiﬁcation of the owner to be programmed into the

transmitter. The user name appears during the startup process at the lower left

corner of the startup screen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info