Bedienungsanleitung Spektrum DX8 (Seite 30 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite





With the Elevator to Flap mix screen displayed, rotate the roller to highlight Ele >

Flp then press the roller. Now rotate the roller to select programmable Mix, 1, 2,

3, 4, 5, or 6 and press the roller. The Mix screen appears.



The Master channel is the controlling channel. The slave is the channel, the

master will be mixed to. The slave channel will follow the master channels input

based on the rate that is programmed.

Rotate the roller to highlight the left INH then press the roller to access the master

channel. Rotate the roller to select the desired master channel. When selected,

press the roller to accept that master channel.

Rotate the roller to highlight the right INH then press the roller to access the slave

channel. Rotate the roller to select the desired slave channel. When selected,

press the roller to accept that slave channel.



Rotate the roller to highlight Sw: at the bottom of the screen. Press the roller to

access the switch select function then select the desired switch to turn on/off the

aileron to rudder mix. If you select On, the mix will always be on.



Rotate the roller to highlight the desired rate then press the roller to highlight that

rate. Rotate the roller to adjust the value. You can reverse the direction of the slave

channel with positive + and negative - values.

Adjust the rate for all both directions/values.

To verify that the programmable mix is working properly and in the correct

direction, place the correlating switch in the active positions, move the

programmed master channel and observe the slave channel. The slave channel

should move accordingly.



The offset function establishes the point at which the two mix rates converge.

Typically this rate is center or 0%. If an offset is needed do the following:



Rotate the roller to highlight Offset then press the roller to highlight the Offset

rate. Rotate the roller to adjust the value. Positive + and negative - values are

available shifting the offset in either direction. Press the roller to accept the offset

value.

Trim Include

The trim include function applies trim to the slave channel when the master

channel you select is a channel that has trim (throttle, aileron, elevator and

rudder). Typically, this is used when more than one channel is used to operate a

primary control surface (dual rudder servos, etc.) With trim include activated, the

master channel’s trim affects the master and slave channels.



Rotate the roller to highlight Trim. Press the roller to toggle between INH and ACT.





The Tail Curve programming functions nearly identically to the Throttle and Pitch

curve programming. You can assign four separate Tail curves or a common Tail

curve to 2 or more ﬂight modes. A graph displays at the left side of the screen to

help you adjust the Tail curves. An Expo function is available that smooths out

the curve.

Note: Only use tail curves when the gyro is in the conventional gain (non-

heading hold) mode.



With the transmitter on and the main or telemetry screen displayed, press the

roller. The Function list displays.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info