Bedienungsanleitung Spektrum DX8 (Seite 31 von 42) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite



Rotate the roller to highlight Tail Curve then press.



Highlight the desired ﬂight mode at the bottom of the screen then press to select.

Note that the selected ﬂight mode will darken conﬁrming the selection.

N= Normal

1= Stunt 1

2= Stunt 2

H= hold



Move the ﬂight mode switch in the position you wish to adjust the curve to.

Highlight one of the ﬁve available Pitch curve values (Low, 25%, 50%,75%,

High). Press the roller to access that value.

Rotate the roller to adjust the selected point to the desired output position. Note

the position on the graph at the left of the screen.

Repeat this for all desired points.



Rotate the roller to highlight EXPO then press to toggle between INH and ACT.



The DX8 offers eight mixes in helicopter model type. You can program a cyclic-

to-throttle mix to advance the throttle when aileron, elevator and or rudder inputs

are given. This prevents rpm decay during cyclic and rudder inputs. A Swashplate

Mix mixes Aileron to Elevator and Elevator to Aileron to adjust swashplate timing.

Six programmable mixes allow the mixing of any channel to any other channel.

You can assign Mixes to activate in various ﬂight modes as well as with the gear

switch. Programmable mixes include a trim offset function that adjusts the mix

crossover point and a trim include function that applies the master’s trim to the

slave channel.



With the transmitter on and the main or telemetry screen displayed, press the

roller. The Function list displays.

Rotate the roller to highlight Mixing then press. The Cyclic to throttle mix appears

on the screen.



Cyclic-to-throttle mix prevents rpm decay when aileron, elevator and or rudder

inputs are given. This mix advances the throttle position with cyclic or rudder

control to maintain rpm. At full throttle, programming prevents the throttle from

overdriving the servo.

Important: When using a governor, Cyclic to throttle mix is not recommended.



Rotate the roller to highlight the desired box at the bottom of the screen. Press the

roller to darken the box and activate Cyclic Mix in that ﬂight mode position. You

can highlight more than one ﬂight mode position. If all boxes are highlighted, the

C Mix function is always on. If no boxes are highlighted, the function is always off.

N= Normal

1= Stunt 1

2= Stunt 2

H= Hold

M=Mix



Rotate the roller to highlight the desired rate then press. Rotate the roller to adjust

the value. The available positive + and negative - values reverse the direction of

the throttle mix.

Adjust the rates for all desired channels.

To verify that Cyclic mix is working properly and in the correct direction, place the

ﬂight mode switch in one of the active positions. Move the programmed cyclic or

rudder channel noting the throttle position. The throttle position should increase.

If it decreases then the opposite value (positive vs. negative) is needed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info