Bedienungsanleitung Spektrum DX8 (Seite 9 von 100) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite



STEP #9



You can use aileron differential to reduce unwanted yaw characteristics during a

roll. In aerobatic airplanes adjusting differential provides an axial roll (minimum

displacement of yaw during a roll). You can program up to three Differential

values and assign them to a switch. Positive + and negative – differential is

available. However, more up-aileron travel is normally required than down

aileron.

 The Differential function is only available if Dual Aileron, Flaperon, 2

aileron 1 ﬂap, 2 ailerons and 2 ﬂaps or Elevon is selected in Wing Type.



In the Function List rotate the roller to highlight Differential then press the roller.

Differential defaults to Inhibit. Press the roller to highlight Inhibit then select one

of the following switch positions:

On - Always on

Ail D/R - Aileron Dual rate switch

Ele D/R - Elevator Dual rate switch

Rud D/R - Rudder dual rate switch

F Mode - Flight Mode switch

Flap - Flap switch

Aux 2-Auxiliary 2

Gear - Gear Switch

Mix-Mix switch

Press the roller to accept the desired switch. The differential adjustment screen

displays.

Highlight the desired differential position/value and press the roller to access.

Rotate the roller to change the value then press the roller. Repeat for all desired

switch positions.

Positive differential values provide more up than down aileron travel. Negative

differential values provide more down than up travel.

STEP #10





You can program the timer to start when the throttle is raised above a

preprogrammed position.

To reset the timer, from the main screen press the Clear button.



In Function List rotate the roller to highlight Timer. Press the roller to access the

Timer screen.



Rotate the roller to highlight the Mode function then press the roller to access

the Mode function. Rotate the roller to select Inhibit, Count Down or Stopwatch.

When the desired timer mode is selected, press the roller to accept the mode type.

To Program a Time

Rotate the roller to highlight Time then press the roller to access the Time

function. You can highlight the seconds or minutes. Press the roller to access

minutes or second. Rotate the roller to select the desired time. Press the roller to

accept.



Rotate the roller to highlight Start then press the roller to access the Start

function. Select Throttle or Throttle 1-Time then press the roller.

Throttle 1-time - The timer starts when you exceed the programmed throttle

position. It continues regardless of the throttle position.

Throttle - The timer starts when you go above the programmed throttle position.

Anytime you lower the throttle below the programmed position, the timer pauses

then continues when you raise the throttle above that position. This is useful for

ﬂying electric models where the motor run time, not the ﬂight time, is important.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info