Bedienungsanleitung Spektrum DX8 (Seite 16 von 100) (Englisch)

708059

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite





Rotate the roller to select the desired governor value. Press the roller to access

and adjust the value. Afterwards, press the roller to accept the value.

 The displayed value is the corrected governor value. 0% represents

1.500ms or off with most governors.

Repeat this for all desired governor values.

STEP #12



Cyclic-to-throttle mix advances the throttle position with cyclic or rudder control

to maintain rpm. If you advance the stick to full throttle, the system will not

change throttle rate. This prevents overdriving the throttle servo.

 When using a governor, Cyclic to throttle mix is not recommended.



In the Function list, press Mixing to access the C-Mix screen. In the C-Mix

functions rotate the roller to highlight the desired box at the bottom of the screen.

Press the roller to darken the box and activate Cyclic Mix in that ﬂight mode

position. You can highlight more than one ﬂight mode position. If you highlight

all boxes, the C-Mix function will always be on. If no boxes are highlighted, the

function will always be off.

N= Normal

1= Stunt 1

2= Stunt 2

H= Hold

M= Mix switch



Rotate the roller to highlight the desired rate then press the roller. Rotate the roller

to adjust the value, then press the roller to accept the value. Note the available

positive + and negative - values. Positive values add throttle while negative values

subtract throttle mix. Adjust the rates for all desired channels.

To verify that Cyclic mix is working properly and in the correct direction, place the

ﬂight mode switch in one of the active positions. Move the

programmed cyclic or rudder channel noting the throttle position. The throttle

position should increase. If it decreases then the opposite value (positive vs.

negative) is needed.

STEP #13



You can use Cyclic Mix to correct swashplate timing issues. This function mixes

Elevator to Aileron to correct any rolling tendencies when elevator is applied and

Aileron to Elevator to correct pitching tendencies when aileron is applied. When

adjusted correctly the Cyclic Mix causes the helicopter to roll and ﬂip accurately

and on axis.



In the Mixing function, rotate the roller to highlight Cyclic Mix then press the

roller. Select Swashplate and press the roller. The Swashplate Mix screen appears.



Rotate the roller to highlight the desired box at the bottom of the screen. Press

the roller to darken the box activating Swash Mix in that ﬂight mode position. You

can highlight more than one ﬂight mode position. If all boxes are highlighted, the

C-Mix function will always be on. If no boxes are highlighted, the function will

always be off.

N= Normal

1= Stunt 1

2= Stunt 2

H= Hold

M= Mix switch



Rotate the roller to highlight the desired rate then press the roller to access the

rate. Rotate the roller to adjust the value and press the roller to accept. You can

reverse the direction of the slave channel with positive + and negative – values.

Adjust the rate for all desired Swashplate values.

Verify that the Swash mix is working properly and in the correct direction by

placing the ﬂight mode switch in one of the active positions. Then, move the

programmed cyclic master channel aileron or elevator to its full travel and hold

this position. Now change the ﬂight mode to a position that the swash mix is

inactive in. Note the movement of the slave channel on the left side of the monitor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Spektrum DX8 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Spektrum DX8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info