Bedienungsanleitung Stanley FMC792 (Seite 9 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720710

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

(Original instructions)

u Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 18°- 24°C. DO NOT charge the battery pack in

an air temperature below +4.5°C, or above +40.5°C. This

is important and will prevent serious damage to the battery

pack .

u The charger and battery pack may become warm to touch

while charging. This is a normal condition, and does not

indicate a problem. To facilitate the cooling of the battery

pack after use, avoid placing the charger or battery pack

in a warm environment such as in a metal shed, or an

uninsulated trailer

u If the battery pack does not charge properly:

u Check current at receptacle by plugging in a lamp or

other appliance

u Check to see if receptacle is connected to a light switch

which turns power off when you turn out the lights.

u Move charger and battery pack to a location where the

surrounding air temperature is approximately 18°-

24°C.

u If charging problems persist, take the appliance, battery

pack and charger to your local service center.

u The battery pack should be recharged when it fails to

produce sufficient power on jobs which were easily done

previously. DO NOT CONTINUE to use under these

conditions. Follow the charging procedure. You may also

charge a partially used pack whenever you desire with no

adverse affect on the battery pack.

u Foreign materials of a conductive nature such as, but

not limited to, steel wool, aluminium foil, or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean.

u Do not freeze or immerse charger in water or any other

liquid.

Warning! Shock hazard. Do not allow any liquid to get inside

charger. Never attempt to open the battery pack for any

reason.

If the plastic housing of the battery pack breaks or cracks,

return to a service center for recycling.

Installing and removing the battery pack from the

appliance

Warning! Make certain the lock-off button is not engaged to

prevent switch actuation before removing or installing battery.

To install battery pack

Insert battery (A1) into appliance until an audible click is

heard (Figure A). Ensure battery pack is fully seated and fully

latched into position.

To remove battery pack

Depress the battery release button (B1) as shown in Figure B

and pull battery pack out of appliance.

Operation

Warning! Read the section titled Nailer Safety Warnings at

the beginning of this manual. Always wear eye and ear protec-

tion when operating this tool.

Keep the nailer pointed away from yourself and others. For

safe operation, complete the following procedures and checks

before each use of the nailer.

Warning! To reduce the risk of personal injury, disconnect

battery pack from tool and engage trigger lock-off before

performing maintenance, clearing a jammed nails, leaving

work area, moving tool to another location or handing the tool

to another person.

Warning! Keep ngers AWAY from trigger when not driving

fasteners to avoid accidental ring. Never carry tool with nger

on trigger.

u Wear proper eye, hearing and respiratory protection.

u Remove battery pack from tool and engage trigger lock-

off.

u Lock the pusher in the back position and remove all nail

strips from the magazine.

u Check for smooth and proper operation of contact trip and

pusher assemblies. Do not use tool if either assembly is

not functioning properly.

u Never use a tool that has damaged parts.

To operate the nailer

Warning! The contact trip needs to be depressed followed by

a full trigger pull for each nail followed by a release of both the

contact trip and trigger after each nail.

Warning!The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

u Fully depress contact trip against the work surface.

u Fully pull trigger and motor will start. (nail will drive into

work surface).

u Release trigger.

u Lift contact trip off work surface.

u Repeat the above 4 steps for next application

Preparing the tool

Warning! NEVER spray or in any other way apply oil, lubri-

cants or cleaning solvents inside the tool. This can seriously

affect the life and performance of the tool.

Warning! The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

u Read the Safety Instruction section of this manual.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC792 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info