Bedienungsanleitung Stanley FMC792 (Seite 10 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720710

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

(Original instructions)

u Wear eye and ear protection.

u Remove battery from tool and fully charge.

u Ensure magazine is empty of all fasteners.

u Check for smooth and proper operation of contact trip and

pusher assemblies. Do not use tool if either assembly is

not functioning properly.

u Keep tool pointed away from yourself and others.

u Insert fully charged battery pack.

Loading the Tool

Warning! Keep the tool pointed away from yourself and oth-

ers. Serious personal injury may result.

Warning! Never load nails with the contact trip or trigger

activated.

Warning! Always remove battery pack before loading or

unloading nails.

Warning! The battery should always be removed and the trig-

ger lock-off is engaged whenever any adjustments are made

or when tool is not in use.

Warning! Keep ngers clear of pusher to prevent injury.

u Insert fasteners into the bottom of the magazine (9).

u Pull pusher (10) downward until the nail follower

(C1) falls behind the nails as shown in gure C.

u Release the pusher (10).

Unloading the Tool

Warning!The battery should always be removed and the

trigger lock-off engaged whenever any adjustments are made

or when tool is not in use.

u Press pusher latch release button (12).

u Manually slide nails towards the bottom of the magazine

(9).

u Open the jam clear door (7) on the nosepiece to verify

there are no nails remaining.

Adjusting Depth (Fig. D, E)

The depth that the fastener is driven can be adjusted using

the depth adjustment wheel (3) on the side of the tool.

Warning!To reduce risk of serious injury from accidental

actuation when attempting to adjust depth, Always:

u Remove battery pack.

u Engage trigger lock-off.

u Avoid contact with trigger during adjustments.

Depth settings are on a sliding scale (4). The left side indicat-

ing the deepest and the right side indicating the shallowest.

u To drive a nail deeper, rotate the depth adjustment wheel

(3) downwards. This will slide the depth adjustment indica-

tor (4) to the left on the scale.

u To drive a nail shallower, rotate the depth adjustment

wheel (3) upwards. This will slide the depth adjustment

indicator (4) to the right on the scale.

Work lights (Fig. F)

There are work lights (5) located on each side of the nailer.

Work lights turn on upon depressing the contact trip.

Note: These work lights are for illuminating the immediate

work surface and are not intended to be used as ashlights.

Low Battery Indicator:

The work lights will ash and then turn off completely to

indicate low battery.

Jammed Nail Indicator:

The work lights will ash continually if a nail becomes jammed

in the nose piece (see Clearing a jammed nail).

Stall Release (Fig. G)

Warning!If a stall occurs, the tool will disable itself and will re-

quire you to reset it. To do so, follow instructions on clearing a

stalled condition. Next remove battery pack and then reinsert

battery pack. The tool will now be operational. If the nailer is

used in a rigorous application where all available energy in the

motor is used to drive a fastener, the tool may stall. The driver

blade did not complete the drive cycle and the jam/stall indica-

tor will ash. Rotate the stall release lever (6) on the tool and

the mechanism will release as shown in gure G.

Note! The tool will disable itself and not reset until the battery

pack has been removed and reinserted. If the unit continues

to stall please review the material and fastener length to be

sure that it is not too rigorous an application. If the driver

blade does not automatically return to the home position after

rotating the stall release lever, proceed to “clearing a jammed

nail”.

Clearing a Jammed Nail (Fig. H)

Warning!To reduce the risk of personal injury, disconnect

battery pack from tool and engage trigger lock-off before

performing maintenance, or clearing a jammed nail.

If a nail becomes jammed in the nosepiece, keep the tool

pointed away from you and follow these instructions to clear:

u Remove battery pack from tool and engage trigger lock-

off.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC792 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info