Bedienungsanleitung Stanley FMC792 (Seite 11 von 120) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

720710

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

ENGLISH

(Original instructions)

u Rotate the stall release lever (6) on the tool to release the

driver blade and clear the jam. If tool is still jammed follow

the 9 steps listed below:

u Pull pusher downward until it locks in place then tip the

tool over so the nails slide freely out from the bottom of

the magazine.

u Lift the jam clearing latch (7) then pull up to open front

door (14).

u Remove bent nail, using pliers if necessary.

u If driver blade is in the down position, insert screwdriver

or other rod into nosepiece and push driver blade back

in position.

u Close the front door and engage the wire form (13)

under the two arms (15) on the contact trip. Push jam

clearing latch down (7) until it locks in place.

u Reinsert nails into magazine (see Loading the Tool).

u Pull pusher (10) downward until the nail follower (C1)

falls behind the nails as shown in gure C.

u Reinsert battery pack.

u Disengage trigger lock-off (2), allowing the trigger to be

actuated.

Warning!If a jam occurs, the tool will disable itself and will

require you to reset it. To do so, follow instructions on clearing

the jammed nail. Next remove battery pack and then reinsert

battery pack. The tool will now be operational.

Note!Should nails continue to jam frequently in contact trip,

have tool serviced by an authorized Stanley Fat Max service

center.

Cold Weather Operation

When operating tools at temperatures below freezing:

u Keep tool as warm as possible prior to use.

u Actuate the tool 5 or 6 times into scrap lumber before

using.

Hot Weather Operation

Tool should operate normally. However, keep tool out of direct

sunlight as excessive heat can deteriorate bumpers and other

rubber parts resulting in increased maintenance.

Belt Hook (Fig. I-J)

Warning!Remove nails from magazine before making any

adjustments or servicing this tool. Failure to do so may result

in serious injury.

u Remove battery pack from tool, and engage trigger lock-

off.

u With a screwdriver remove screw from hang hook cavity

on the base of the tool (16).

u Place the front lip of the hang hook (11) into the cavity on

the base of the tool (16) as shown in Figure I.

u Secure the hang hook (11) with the supplied screw (17)

and rmly tighten with a screwdriver as shown in Figure J.

u Replace battery pack.

Replacement parts

Warning!To reduce the risk of personal injury, disconnect

battery pack from tool and engage trigger lock-off before

performing maintenance, or clearing a jammed nail.

The tool comes equipped with a spare no mar tip located on

the side of the nail magazine.

u To replace the no mar pad, simply pull off the old no mar

pad and ret the new no mar pad onto the contact trip.

Use only identical replacement parts. For a parts list or to

order parts, visit our service website at www.stanley.eu/3co.

uk. You can also order parts from your nearest

Stanley Fat Max Factory Service Center or Stanley Fat Max

Authorized Warranty.

Troubleshooting

If your appliance seems not to operate properly, follow the

following instructions.

If this does not solve the problem, please contact your local

Stanley Fat Max repair agent.

Warning! Before proceeding, unplug the appliance.

Problem Possible Cause Possible Solution

Unit will not start. Battery pack not

installed properly.

Battery pack not

charged.

Trigger lock-off is

engaged.

Check battery pack

installation.

Check battery pack charging

requirements.

Disengage trigger lock-off.

Tool doesn’t

actuate.

(Headlights on,

motor does not

run)

Motor stops running

after 2 seconds.

Normal operation; release

trigger or contact trip and

re-depress.

Tool doesn’t

actuate.

(Headlights

ash)

Low battery charge or

damaged battery.

Charge or replace battery.

Tool doesn’t

actuate.

(Headlights ash

continuously)

Jammed fastener / tool

stalled.

Jammed mechanism

Remove the battery, rotate the

stall release lever. Clear the

jammed fastener, and reinsert

battery pack.

See authorized service center.

Tool doesn’t

actuate.

((Headlights on,

motor runs,

driver blade

stuck down)

See authorized service center.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FMC792 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info