Bedienungsanleitung Stanley FME720 (Seite 10 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

622174

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

ENGLISH

(Original instructions)

Features

This tool includes some or all of the following features.

1. Laser on/off switch

2. Main operating handle

3. On/off switch

4. Motor housing

5. Moveable lower guard

6. Table extension material stop (right)

7. Table extension (right)

8. Kerf plate

9. Mitre clamp

10. Mitre lock knob

11. Mitre detent lever

12. Mitre position adjustment pointer

13. Mitre scale

14. Rotating table

15. Bench mounting holes

16. Clamp locating mounts

17. Table extension (left)

18. Table extension material stop (left)

19. Table extension securing knob

20. High sliding fence clamp

21. Left-hand fence

22. Left-hand high sliding fence

23. 33.9° bevel pin

24. Rear carry handle

25. Saw dust outlet

26. Metal upper guard

27. Front carry handle

28. Removable brush box

29. Carriage

30. Bevel lock handle

31. Bevel scale

32. Right-hand fence

33. Laser

34. Saw blade

35. Spindle lock button

36. Saw arm release lever

Fig. R

53. Clamp

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Note: This tool is accurately adjusted before shipping from

the factory. Check the following accuracy and readjust them if

necessary in order to obtain the best results in operation

Laser beam

The laser beam alignment is set at manufacturing source and

is not user adjustable.

Mitre angle adjustment

The sliding compound mitre saw scale can be easily read

showing mitre angles from 0° to 47° to the left and the right.

The most common angle cut setting slots have positive stops,

permitting fast adjustments to the required position. Follow the

process below for quickest and most accurate adjustments.

Mitre clamp (g. B)

The mitre clamp (9) allows the saw to be set to specic angles

other than the preset angles of 0°, 15°, 22.5°, 31.6°, and 47°

which are set using the mitre detent lever (11).

Adjusting the bevel stops at 90° and 45° (g. C - F)

u Loosen the bevel lock handle (30) and move the cutting

head all the way to the right and tighten the bevel lock

handle.

u Use a square to set the blade at 90° to the table (g. D).

u If an adjustment is necessary, loosen the lock nut (41) and

adjust the bolt (40) with the wrench so that the blade is

90° to the table.

u Tighten the lock nut (41).

u Align the bevel indicator (39) with the 0° mark by adjusting

the screw (38).

When adjusting the 45° stop, make sure that the left-hand

high sliding fence (22) is adjusted so that the cutting head can

be moved to the 45° position (g. E).

u Release the high sliding fence clamp (20) and move the

high sliding fence (22) away from the blade.

u Tighten the high sliding fence clamp (20).

u Pull out the 33.9° bevel pin (23) and follow the same

procedures for the 90° but move the cutting head to the

left and use the lock nut (43) and adjustment bolt (42).

Adjusting the fence (g. G - H)

u Lower the cutting head and push in the lock pin (46).

Make sure that the table is in 0° mitre position.

u Place a combination square against the left-hand fence

(21) and next to the saw blade (34) (g. G).

u If the blade does not contact the square along it’s length,

loosen the three screws (44) (g. H) and adjust the fence.

u Tighten the three screws (44).

Bench mounting (g. I)

Note: We highly recommend that you bolt this mitre saw

securely to a work bench to gain the maximum stability of

your machine. Make sure that the machine is xed to a bench

whenever possible.

u Locate and mark the four bolt holes on the bench.

u Drill the bench with an Ø10 mm drill bit.

u Bolt the mitre saw onto the bench with bolts, washers and

nuts.

Note: These fasteners are not supplied with the tool.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME720 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info