Bedienungsanleitung Stanley FME720 (Seite 11 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

622174

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

ENGLISH

(Original instructions)

Use

u Place your hands no closer than 150 mm from the blade.

u Hold the workpiece tightly to the table and the fence when

cutting. Keep your hands in position until the switch has

been released and the blade has completely stopped.

u Always make dry runs (without power) before nish cuts

so that you can check the path of the blade.

u Do not cross your hands.

u Keep both feet rmly on the oor and maintain proper

balance.

u As you move the saw arm left and right, follow it and stand

slightly to the side of the saw blade.

u Sight through the guard louvres when following a pencil

line.

Warning! Always t a dust extration device when cutting

wood. A dust bag is provided. Fit the dust bag by squeezing

the metal clamps together on the opening of the dust bag then

placing it over the saw dust outlet (25) releasing the clamps

will then allow the dust bag to grip the saw dust outlet tightly.

Warning! Make sure that the workpiece is securely held

in place with the clamp before any cutting operation. The

minimum size of worpiece that can be used is (L) 150mm X

(W) 50mm X (H) 3mm. Severe personal injury can occur if the

workpiece is not secured.

Basic pullover mitre saw operations (g. A, H & R)

u Always use the clamp (53) to hold the workpiece rmly.

Two holes (45 - g. H) and (16 - g. A) are provided for the

clamp (53 g. R). Ensure that the clamp (53) is pushed

rmly into the retaining hole before tightening the clamp

on the workpiece

Warning! Make sure that the workpiece is securely held in

place with the clamp before any cutting operation. Severe

personal injury can occur if the workpiece is not secured.

u Always position the workpiece against the fence. Any

piece that is bowed or warped and cannot be held at on

the table or against fence may trap the blade and should

not be used.

Pullover cut (g. I & J)

Warning! Never pull the cutting head assembly and rotating

blade toward you during the cut. The blade may try to climb

up on the top of the workpiece, causing the cutting head

assembly and spinning blade to kick back. Never lower the

rotating saw blade down before pulling the cutting head to the

front of the saw.

u Unlock the carriage (29) with the lock knob (48) and allow

the cutting head assembly to move freely (g. J).

u Move the cutting head to the required mitre angle and

bevel angle in accordance with the mitre cut and bevel cut

procedures.

u Hold the main operating handle (2) and pull the carriage

(29) forward until the centre of the saw blade is over the

front of the workpiece.

u Operate the on/off switch (3) and press the saw arm

release lever (36) to lower the cutting head.

u When the saw reaches full speed, push the main operat-

ing handle (2) down slowly, cutting through the leading

edge of the workpiece.

u Slowly move the main operating handle (2) toward the

fence to complete the cut.

u Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Chop cut

u Slide the cutting head to the rear position as far as it will

go, and lock the carriage (29) with the lock knob (48).

u Operate the on/off switch (3) and press the saw arm

release lever (36) to lower the cutting head.

u When the saw reaches full speed, push the main operat-

ing handle (2) down slowly, cutting through the workpiece.

u Slowly move the main operating handle (2) toward the

fence to complete the cut.

u Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Mitre cut

u Switch the laser on/off switch (1) to on.

u Loosen the mitre detent lever (11) and move the table

to the required angle. There are preset stops at 0°, 15°,

22.5°, 31.6°, and 45°. Tighten the mitre detent lever (11).

u For any other angle use the mitre clamp (9) (g. B) to set

the mitre to the required angle.

u Operate the on/off switch (3), then press the saw arm

release lever (36) and lower the cutting head.

u When the saw reaches full speed, push the main operat-

ing handle (2) down slowly, cutting through the workpiece.

u Slowly move the main operating handle (2) toward the

fence to complete the cut.

u Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Operating the high sliding fence for all bevel and

compound mitre cuts

u The moveable part of the left side of the fence can be ad-

justed to provide maximum support of the work piece near

the blade, while allowing the saw to bevel to a full 47° left.

The sliding distance is limited by stops in both directions.

Adjusting the fence (g. E)

u Loosen the high sliding fence clamp (20) and slide the

fence to the left.

u Make a dry run with the saw switched off and check for

clearance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME720 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info