Bedienungsanleitung Stanley FME720 (Seite 12 von 152) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

622174

Zoom out

Zoom in

Vorherige Seite

1/152

Nächste Seite

ENGLISH

(Original instructions)

u Adjust the fence to be as close to the blade as practical to

provide maximum work piece support, without interfering

with the up and down movement of the arm.

u Tighten the high sliding fence clamp (20) to secure the

fence in place.

Warning! The guide groove can become clogged with saw-

dust. Use a stick or low pressure air to clear the guide groove.

Bevel cut

u Make sure that the high sliding fence is adjusted to the

correct orientation before adjusting the bevel angle.

Note: The saw is tted with a special 33.9° bevel pin (23) for

special crown moulding.

u Loosen the bevel lock handle (30) (g. F) and move the

cutting head to the required angle. Tighten the bevel lock

handle (30).

u Operate the on/off switch, then press the release lever

(36) when the saw reaches full speed, push the main

operating handle (2) down slowly, cutting through the

workpiece.

u When the saw reaches full speed, push the main operat-

ing handle (2) down slowly, cutting through the leading

edge of the workpiece.

u Slowly move the main operating handle (2) toward the

fence to complete the cut.

u Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

u Make sure that the arm is securely locked when bevelling.

Compound cut

u Make sure that the high sliding fence is adjusted to the

correct orientation before adjusting the bevel angle to

make a compound cut.

A compound cut is a combination of mitre cut and bevel cut.

u Switch the laser on/off switch (1) to on.

u Refer to the above procedures to perform this cut.

u When the saw reaches full speed, push the main operat-

ing handle (2) down slowly, cutting through the leading

edge of the workpiece.

u Slowly move the main operating handle (2) toward the

fence to complete the cut.

u Release the on/off switch (3) and allow the blade to stop

before allowing the cutting head to rise.

Base moulding cut

Base moulding can be cut vertical against the fence or at on

the table.

u Refer to the following table:

Settings

Vertical position

(back of moulding is

against the fence)

Horizontal position

(back of moulding is

at on the table)

Bevel angle 0 º 45 º

Moulding position Left side

Right

side

Left side

Right

side

Inside

corner

Mitre angle

Left at

45 º

Right at

45 º

0 º 0 º

Moulding

position

Bottom

against

table

Bottom

against

table

Top

against

nce

Bottom

against

fence

Finished

side

Keep left

side of

cut

Keep

right side

of cut

Keep left

side of

cut

Keep left

side of

cut

Settings

Vertical position

(back of moulding is

against the fence)

Horizontal position

(back of moulding is

at on the table)

Bevel angle

0 º 45 º

Outside

corner

Mitre angle

Left at

45 º

Right at

45 º

0 º 0 º

Moulding

position

Bottom

against

table

Bottom

against

table

Top

against

nce

Bottom

against

fence

Finished

side

Keep left

side of

cut

Keep

right side

of cut

Keep

right side

of cut

Keep

right side

of cut

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley FME720 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info