622174
13
Zoom out
Zoom in
Vorherige Seite
1/152
Nächste Seite
13
ENGLISH
(Original instructions)
Crown moulding cut (g. L)
Crown moulding can only be cut at on the table with this
mitre saw.
u This mitre saw has special mitre stops on 31.6° left and
right and a bevel stop of 33.9° for special crown moulding,
i.e. 52° between the back of the moulding and the top
at surface that ts against the ceiling; 38° between the
back of the moulding and the bottom at surface that ts
against the wall.
u Refer to the following table to make this crown moulding
cut:
Settings Left side Right side
Inside
corner
Mitre
angle
Right 31.6 º Left 31.6 º
Bevel
angle
33.9 º 33.9 º
Moulding
position
Top against fence Bottom against fence
Finished
side
Keep left side of cut Keep left side of cut
Outside
corner
Mitre
angle
Right 31.6 º Left 31.6 º
Bevel
angle
33.9 º 33.9 º
Moulding
position
Bottom against fence Top against fence
Finished
side
Keep right side of cut Keep right side of cut
Note: These special stops can not be used with 45° crown
moulding.
Note: Since most rooms do not have angles of exactly 90°,
ne tuning is needed, always make a test cut to conrm the
correct angles.
Setting the cutting depth (g. M)
The depth of cut can be preset for even and repetitive shallow
cuts.
u Adjust the cutting head down until the teeth of the blade
are at the required depth of cut.
u While holding the upper arm in position, turn the stop knob
(47) until it touches the stop plate (49).
u Check the blade depth by moving the cutting head front
to back through the full motion of a typical cut along the
control arm.
Carrying the tool (g. N)
u Loosen the mitre detent lever (11) (g. B) and turn the
table all the way to the right. Lock the table at the 45°
mitre angle.
u Pull the cutting head to the front of the saw and lock the
carriage with the lock knob (48) (g. J).
u Lower the cutting head and push in the lock pin (46) (g.
H).
u Carry the mitre saw with the front and the rear carrying
handles (24, 27).
Warning! Do not carry the machine by the guard.
Blade and tooth type
Material
Tooth type
600 ~ 100T 24 ~ 100T
TCG ATB
Wood
Lumber
Plywood
Hardwood
Chipboard
Plastic
PVC
ABS
Acrylic
PC
PS
Non-ferrous
metal
Aluminium
Copper
Your mitre saw has been supplied with a negative rake saw
blade. It is advisable to use a negative rake saw blade.
u TCG type - For cutting aluminium sheets, tubing extru-
sions and other non-ferrous metals such as copper, brass.
u ATB type - For general cutting and trimming of wood,
plywood, and sizing pressboard, hardboard, and particle
board, when a neat cut is needed.
Always use a negative rake blade when cutting non-ferrous
metals.
Warning! Do not use any blade that requires a spacer or
spindle ring to t. Only use blades as specied in this manual.
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley FME720 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info