Bedienungsanleitung Stanley STPT0900 (Seite 7 von 11) (Englisch)

720714

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

ENGLISH

(Original instructions)

To install blade into saw

1. Point tool away from body.

2. Rotate blade clamp collar in the direction shown in ﬁg.4.

3. Insert blade shank fully into blade clamp collar.

4. Release blade clamp collar to lock blade into position.

Note: Blade can be installed with the teeth up to assist in

ﬂush-to cutting.

To remove blade from saw

Warning:CUTHAZARD.Turn off and disconnect

tool from power source before making any

adjustments or removing or installing

attachments or accessories.

Warning:Burn hazard. Do not touch the blade

immediately after use. Contact with the blade

may result in personal injury.

1. Rotate blade clamp collar to release position.

2. Remove blade.

Adjustable shoe (ﬁg.5)

Warning: CUT HAZARD. Blade breakage may

occur if the blade does not extend past the shoe

and the workpiece during the cut. Increased risk

of personal injury, as well as damage to the shoe and

workpiece may result.

Warning: CUT HAZARD. Turn off and

disconnect tool from power source before

making any adjustments or removing or installing

attachments or accessories. The shoe will adjust to limit the

depth of cut. Using a M4(5/32in.) hex wrench (not supplied),

loosen the screws (Figure5) and slide the shoe out to the

desired depth then retighten screws securely.

Caution:CUTHAZARD.To prevent loss of

control, never use tool without shoe.

Caution: RISK OF PERSONAL INJURY AND PROPERTY

DAMAGE. Ensure the shoe is locked into position before

using tool.

Flush cutting (ﬁg.6)

• The compact design of the reciprocating saw motor

housing and pivoting shoe permit close cutting to ﬂoors,

corners and other difﬁcult areas.

• To maximize ﬂush cutting capabilities, insert the blade

shaft into the blade clamp with the teeth of the blade

facing up.

• Turn the saw upside down so you are as close to the

work surface as possible.

Metalcutting (ﬁg.7)

• Use a ﬁner blade for ferrous metals and a coarse blade

for non-ferrous materials.

• In thin gauge sheet metals it is best to clamp wood to the

underside of the sheet. This will ensure a clean cut

without excess vibration or tearing of metal.

• Avoid forcing cutting blade as this reduces blade life and

causes costly blade breakage.

Note: Spread a thin ﬁlm of oil or other coolant along the line

ahead of the saw cut for easier operation and longer blade

life.

Pocket cutting-woodonly (ﬁg.8)

• Measure the surface area to be cut and mark clearly with

a pencil, chalk or scriber.

• Insert blade in blade clamp and tighten blade clamp

securely.

• Tip the saw backward until the back edge of the shoe is

resting on the work surface and the fully extended

moving blade will clear the surface.

• Grip unit with both hands, switch motor on permitting

blade to obtain maximum speed.

• Begin a slow, deliberate upward swing with the main

handle of the saw.

• The blade will begin to feed into material. Always be sure

blade is completely through material before continuing

with pocket cut.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STPT0900 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info