720686

Stanley STSM1510 Seite 5

5
Zoom out
Zoom in
Vorherige Seite
1/14
Nächste Seite
5
Key Information You Should Know:
• Cut only with sharp blades. Dull blades cut poorly and
overload the motor.
• If the saw does not cut accurately, refer to the
TROUBLE SHOOTING chart in this manual.
Intended use
Your Stanley Mitre Saw has been designed for fast cutting in
wood, fine finishing or aluminum cutting .
General Safety Instructions
WARNING: When using electric tools, basic
safety precautions should always be followed to
reduce risk of fire, electric shock, and personal
injury, including the following:
Read All Instructions
Safety Warnings: Double Insulation Double
insulated tools are constructed throughout with two
separate layers of electrical insulation or one
double thickness of insulation between you and the tool’s
electrical system. Tools built with this insulation system are
not intended to be grounded. As a result, your tool is
equipped with a two prong plug which permits you to use
extension cords without concern for maintaining a ground
connection.
NOTE: Double insulation does not take the place of normal
safety precautions when operating this tool. The insulation
system is for added protection against injury resulting from a
possible electrical insulation failure within the tool.
Replacement parts: When servicing all tools, USE
IDENTICAL REPLACEMENT PARTS. Repair or replace
damaged cords.
Safety Instructions: Polarized Plugs
To reduce the risk of electric shock, this
equipment has a polarized plug (one blade is
wider than the other). This plug will fit in a
polarized outlet only one way. If the plug does not fit fully
into the outlet, reverse the plug. If it still does not fit, contact
a qualified electrician to install the proper utlet. Do not
change the plug in any way.
Safety Instructions For All Tools
• KEEP GUARDS IN PLACE and in working order.
• REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting
wrenches are removed from spindle before turning tool
on.
• KEEP WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
• DON’T USE IN DANGEROUS ENVIRONMENT. Don’t
use power tools in damp or wet locations, or expose
them to rain. Keep work area well lighted.
• KEEP CHILDREN AWAY. All visitors should be kept at a
safe distance from work area.
• MAKE WORKSHOP KID PROOF with padlocks, master
switches, or by removing starter keys.
• DON’T FORCE TOOL. It will do the job better and be
safer at the rate for which it was designed.
• USE RIGHT TOOL. Don’t force tool or attachment to do
a job for which it was not designed.
• WEAR PROPER APPAREL. No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry which may get
caught in moving parts. Nonslip footwear is
recommended. Wear protective hair covering to contain
long hair.
• ALWAYS WEAR SAFETY GLASSES. Also use face or
dust mask if cutting operation is dusty. Everyday
eyeglasses have only impact resistant lenses, they are
NOT safety glasses.
• SECURE WORK. Use clamps or vise when you cannot
secure the workpiece on the table and against the fence
by hand or when your hand will be dangerously close to
the blade (within 6”).
• DON’T OVERREACH. Keep proper footing and balance
at all times.
• MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for best and safest performance. Follow
instructions for lubricating and changing accessories.
• DISCONNECT TOOLS before servicing; when changing
accessories, such as blades, bits, cutters, and the like.
• REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure switch is in OFF position before plugging in.
• USE RECOMMENDED ACCESSORIES. Consult the
instruction manual for recommended accessories. The
use of improper accessories may cause risk of injury to
persons.
• NEVER STAND ON TOOL. Serious injury could occur if
the tool is tipped or if the cutting tool is unintentionally
contacted.
• CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate
(Original instructions) ENGLISH
… 5 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Stanley STSM1510 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info