Bedienungsanleitung Stanley STSM1510 (Seite 7 von 14) (Englisch)

720686

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

• DO-Use blade guards at all times.

• DO-Keep hands out of path of saw blade.

• DO-Shut off power, disconnect cord from power source

and wait for saw blade to stop before servicing or

adjusting tool.

• DO-Support long work with an outboard tool rest.

• DO-Use only 10 inch diameter blades.

• Do not use saw blades which are damaged or deformed

• DON’T-Attempt to operate on anything but designated

voltage.

• DON’T-Operate unless all clamp handles are tight.

• DON’T-Use blades larger or smaller than those which

are recommended.

• DON’T-Wedge anything against fan to hold motor shaft.

• DON’T-Force cutting action. (Stalling or partial stalling of

motor can cause major damage. Allow motor to reach

full speed before cutting.)

• DON’T-Cut ferrous metals (Those with any iron or steel

content) or any masonry.

• DON’T-Use abrasive wheels. The excessive heat and

abrasive particles generated by them will damage saw.

• DON’T-Allow anyone to stand behind saw.

• DON’T-Apply lubricants to the blade when it’s running.

• DON’T-Place either hand in the blade area when the

saw is connected to the power source.

• DON’T-Use blades rated less than 5500 R.P.M.

• DON’T-Attempt to cut small pieces (hand within 6" of

blade) without clamping.

• DON’T-Operate saw without guards in place.

• DON’T-Perform any operation freehand.

• DON’T-Reach around or behind saw blade.

• DON’T-Place hands closer than 6 inches from the saw

blade.

• DON’T-Reach underneath the saw unless it is turned off

and unplugged. The saw blade is exposed on the

underside of the saw.

• DON’T-Move either hand from saw or workpiece or raise

arm until blade has stopped.

• DON’T-Use without Kerf Plate or when kerf slot is wider

than 3/8"

• DON’T- Carry saw by work extension or other accessory.

CAUTION: Some wood contains preservatives

such as copper chromium arsenate (CCA) which

can be toxic. When cutting these materials extra

care should be taken to avoid inhalation and minimize skin

contact.

CAUTION: Use of this tool can generate dust

containing chemicals known to cause cancer,

birth defects or other reproductive harm. Use

appropriate respiratory protection.

CAUTION: Do not connect unit to electrical

power source until complete instructions are

read and understood.

For your convenience and safety, the following warning

labels are on your mitre saw.

ON MOTOR HOUSING:

WARNING: FOR YOUR OWN SAFETY, READ

INSTRUCTION MANUAL BEFORE OPERATING SAW.

WHEN SERVICING, USE ONLY IDENTICAL

REPLACEMENT PARTS. ALWAYS WEAR EYE

PROTECTION.

ON FENCE:

CLAMP SMALL PIECES BEFORE CUTTING. SEE

MANUAL.

ON GUARD:

DANGER – KEEP AWAY FROM BLADE.

ON GUARD RETAINER PLATE: “PROPERLY SECURE

BRACKET WITH BOTH SCREWS BEFORE USE.”

ON TABLE: (2 PLACES)

ALWAYS TIGHTEN ADJUSTMENT KNOBS BEFORE USE.

KEEP HANDS 6" FROM PATH OF SAW BLADE. NEVER

PERFORM ANY OPERATION FREEHAND. NEVER CROSS

ARMS IN FRONT OF BLADE. THINK! YOU CAN PREVENT

ACCIDENTS. DO NOT OPERATE SAW WITHOUT

GUARDS IN PLACE. NEVER REACH IN BACK OF SAW

BLADE. ALWAYS WEAR EYE PROTECTION. SHUT OFF

POWER AND WAIT FOR BLADE TO STOP BEFORE

SERVICING, ADJUSTING TOOL, OR MOVING HANDS.

(Original instructions) ENGLISH

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STSM1510 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info