Bedienungsanleitung Stanley STSM1510 (Seite 8 von 14) (Englisch)

720686

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Electrical Connection

Be sure your power supply agrees with the nameplate

marking. A voltage decrease of 10 percent or more will

cause a loss of power and overheating. All B&D tools are

factory tested. If this tool does not operate, check the power

supply.

Familiarization

Place the saw on a smooth, ﬂat surface such as a

workbench or strong table. Examine Figures 1 & 2 and refer

to the parts description to become familiar with the saw and

its various parts. The following section on adjustments will

refer to these terms and you must know what and where the

parts are. The part name is followed by the corresponding

part number Example - lock down pin (10). Press down

lightly on the operating handle and pull out the lock down

pin (10), as shown in Figure 3. Gently release the downward

pressure and allow the arm to rise to its full height. Use the

lock down pin when carrying the saw from one place to

another. Use the operating handle (1) to transport the saw

or the hand indentations (11) shown in Figure 2 after

unplugging.

Speciﬁcations

Capacity of cut

47° mitre left and right

47° bevel left

0° mitre -Max. Height 3-1/2” -Max. Width 5-1/2”

45° mitre -Max. Height 3-1/2” -Max. Width 4-1/8”

45° bevel -Max. Height 2-1/2” -Max. Width 5-1/2”

Bench Mounting

Bench mounting holes (8) are provided in all four feet to

facilitate bench mounting, as shown in Figure 1. (Two

different sized holes are provided to accommodate different

sizes of screws. Use either hole, it is not necessary to use

both.) Always mount your saw ﬁrmly to prevent movement.

To enhance the tool’s portability, it can be mounted to a

piece of 1/2" or thicker plywood which can then be clamped

to your work support or moved to other job sites and

reclamped.

NOTE: If you elect to mount your saw to a piece of plywood,

make sure that the mounting screws don’t protrude from the

bottom of the wood. The plywood must sit ﬂush on the work

support. When clamping the saw to any work surface, clamp

only on the clamping bosses where the mounting screw

holes are located. Clamping at any other point will interfere

with the proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be

sure the mounting surface is not warped or

otherwise uneven. If the saw rocks on the surface,

place a thin piece of material under one saw foot until the

saw sits ﬁrmly on the mounting surface.

Installing a New Saw Blade

(UNPLUG THE MITRE SAW)

DO NOT USE FERROUS METAL or masonry cutting blades

in this saw

• Loosen hex bolt on center cover counter clockwise with

box wrench.

• Lift up the safe cover and center cover.

• Press down the lock to lock spindle.

• Loosen hex bolt clockwise with box wrench, then

dismount the bolt and ﬂange.

• Mount the blade of saw on spindle. Make sure that the

arrow direction on surface of saw blade is same as one

of the cover.

Note: There are two different internal diameters of cutter in

inner plate which have steel stamp marked 25.4mm 16mm.

When mounting, the outer diameter of inner plate must be

correspondent with the internal diameter of saw blade.

• Mount ﬂange and hex bolt.

• Press axle lock and tighten hex bolt counter clock wise

with box wrench ﬁrmly, then tighten hex bolt clockwise to

ﬁx centre cover.

Note: Only use attached wrench when mounting or

dismounting saw blade. When dismounting saw blade, lift up

safe cover and centre cover. Loosen hex bolt with box

wrench and disassemble hex bolt, ﬂange and saw blade.

NEVER DEPRESS THE SPINDLE LOCK PIN WHILE THE

BLADE IS ROTATING.

• Be sure to hold the guard bracket down and ﬁrmly

tighten the guard bracket screw when you ﬁnish installing

the saw blade. Failure to do so will cause serious

damage to the saw.

Assembling and Adjusting Your Saw

PERFORM ALL ASSEMBLY WITH SAW UNPLUGGED.

Attach Mitre Clamp Handle

Remove the mitre clamp handle (4) from the plastic parts

bag and carefully thread it into the bracket in the front of the

saw.

Attaching Dust Bag

A zippered cloth dust bag is included with your saw. To

attach the bag, ﬁt the plastic opening ﬁrmly over the dust

spout (9).

NOTE: The saw can also be used with a vacuum cleaner

hose attached to the dust spout or without any attachment.

Adjustments

PERFORM ALL ADJUSTMENTS WITH THE MITRE SAW

UNPLUGGED

ENGLISH (Original instructions)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Stanley STSM1510 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info