Bedienungsanleitung Steinel IS 2160 (Seite 7 von 48) (Alle Sprachen)

593151

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Installation instructions



Dear Customer,

Congratulations on pur-

chasing this STEINEL Inf-

rared Sensor and thank

you for the conﬁ dence

you have shown in us.

You have chosen a high-

quality product that has

been manufactured,

tested and packed with

the greatest care.

Please familiarise yourself

with these instructions

before attempting to in-

stall the sensor since

prolonged reliable and

trouble-free operation will

only be ensured if it is

installed properly.

We hope your new Infra-

red Sensor will give you

lasting satisfaction.

Disconnect the power

before attempting any

work on the motion

detector.

The electrical connec-

tion lead must be dead

during installation.

Therefore, switch off

the power ﬁ rst and

use a voltage tester to

check that the power

supply is disconnected.

Installation of the

sensor involves work

on the mains power

supply. This work must

therefore be carried

out professionally in

accordance with the

applicable wiring regu-

lations and electrical

operating conditions.

(

D - VDE 0100,

A - ÖVE-EN 1,

 - SEV 1000).

Please note that the

sensor must be pro-

tected by a 10 A circuit

breaker. The mains

supply lead must be

no greater than 10 mm

in diam-eter.

Safety warnings

Principle

The integrated pyroelec-

tric infrared detector

senses the invisible heat

radiated from moving

objects (people, animals,

etc.). The heat detected is

electronically converted

into a signal that switches

on loads (e.g. a light) con-

nected to it. Heat is not

detected through obsta-

cles, such as walls or

panes of glass. Heat ra-

diation of this type will,

therefore, not trigger the

sensor.

With a detection angle of

160° and a max. reach of

12 m the sensor watches

over an area of approx.

165 m

. If you only wish

to cover a smaller area,

reach may be reduced

by tilting the sensor unit.

Using the swivel mount

supplied, the sensor

unit can also be turned

horizontally, making it

possible to target the

detection zone exactly

as you choose. The

detection angle can also

be adjusted to suit individual

requirements by ﬁ tting

shrouds.

Important: the safest mo-

tion detection is obtained

when the device is moun-

ted and aligned laterally to

the walking direction and

no obstacles (such as

trees and walls, for ex-

ample) obstruct the view.

(s. ﬁ g. page 2)

Installation

(s. ﬁ g. page 3)

The site of installation

should be at least 50 cm

from a light because heat

radiated from it may trig-

ger the sensor uninten-

tionally. To obtain the spe-

ciﬁ ed reach of 12 m, the

sensor should be installed

at a height of approx. 2 m.

Please ob-serve the safe-

ty warnings on page 12.

Installation procedure:

1. Undo screws on hous-

ing 1 2. Do not detach

wir-ing from terminal

block, but gently pull

entire terminal assembly,

including sensor unit 2

(cylindrical section), to

remove it.

3. Hold mounting plate 3

against wall/ceiling, mark

drill holes, paying atten-

tion to wiring runs con-

cealed in wall/ceiling. Drill

holes, insert wall plugs

(6 mm). 4. Break open

pre-punched cable entry

holes as appropriate for

concealed 4 or surface-

mounted 5 installation,

insert grommets, pierce

and pass cable through.

Note: For surface-mount-

ed wiring, it is recommen-

ded to install the swivel

mount 6 (see below).

Alternatively, the unit may

be pierced at the thinner

section to pass the cable

through. 5. Screw mount-

ing plate 3 to wall.

6a) Connecting the

mains lead

The mains lead consists of

a 2-3 phase cable

L = phase conductor

N = neutral conductor

PE = protective-earth

conductor

If you are in any doubt,

you must identify the

cables using a voltage te-

ster; then disconnect the

power supply again.

The phase (L) and neutral

conductor (N) are connec-

ted according to terminal

assignment. The protecti-

ve-earth conduct-or is

connected to the earth

terminal .

A mains switch for ‘ON’

and ‘OFF’ switching can

of course be installed in

the mains lead.

6b) Connecting the load

supply lead

The load supply lead (e.g.

light) is also a 2 to 3-core

cable which is connected

to terminals N and L’. The

live conductor must be

connected to the terminal

marked L’.

Connect the neutral con-

ductor to the terminal

marked N together with

the neutral conductor of

the mains power supply

lead. The protective-earth

conductor is connected to

the earth terminal .

7. Once wiring is complet-

ed, insert terminal block

together with sensor unit

2 into mounting plate 3,

ﬁ t housing cover 1 and

secure in place with faste-

ning screws.

The swivel mount 6 allows

you to turn the motion

detector horizontally. This

provides additional adju-

stment for the detection

zone.

1. Press cupped pieces

7 out of swivel mount 6

provided with sensor unit.

2. Hold swivel mount 6

against wall and mark drill

holes, drill the holes, insert

wall plugs, pass cable

through. Connect as de-

scribed in „Installation“.

3. Pass screws through

Installation with swivel mount

cupped pieces 7 and

secure swivel mount 6 in

such a way that the screw

head is positioned on the

smooth side and the

domed side rests against

the mounting plate 3 (see

diagram).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel IS 2160 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info