Bedienungsanleitung Steinel IS 2160 (Seite 8 von 48) (Alle Sprachen)

593151

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

The system can be put into

operation once the sensor

has been connected and

installed. Two setting con-

Switch-off delay

(time setting)

The chosen light ‘ON’ time

can be varied continuous-

ly from approx. 8 sec. to a

maximum of 35 min. The

shortest period, approx.

8 sec., is selected by

turning the control fully

clockwise. The longest

period, approx. 35 mins.

is selected by turning the

control fully anticlockwise.

It is recommended to

select the shortest time

for adjusting the detection

zone and for performing

the walk test. Any move-

ment in the detection

zone will re-activate the

time setting.

Twilight setting

(response threshold)

The chosen detector

response threshold can

be adjusted continuously

from approx. 2 lux to 2000

lux. Turning the control

fully clockwise will select

daytime operation at ap-

prox. 2000 lux.

Turned fully anti-clock-

wise, the control is set to

dusk-to-dawn operation

at approx. 2 lux. When

adjusting the detection

zone and for the perform-

ance test in daylight, the

adjusting screw must be

turned fully clockwise.

Functions

8 sec. – 35 min.

2 – 2000 lux

trols are provided on the

bottom of the unit.

Reach adjustment

(s. ﬁ g. page 4)

Reach can be reduced by

tilting (70°) the sensor.

The sensor can be turned

horizontally through 40°

(only with swivel mount) to

align the detection zone

in exactly the way you

require.

The adhesive shrouds

provided may be used

to adjust the sensor‘s

detection angle to suit

individual requirements.

This makes it possible,

for example, to blank out

neighbouring premises

from detection or

speciﬁ cally target paths.

Precision adjustment using shrouds

(s. ﬁ g. page 4)

pose. Weather conditions

may affect the way the

motion detector works.

Strong gusts of wind,

snow, rain or hail may

cause the light to come

‘on’ when it is not wanted

because the sensor is

unable to distinguish sud-

den changes of tempera-

ture from sources of heat.

The detector lens may be

cleaned with a damp cloth

if it gets dirty (do not use

cleaning agents).

Operation/Maintenance

The Infrared Sensor is

suitable for switching light

‘on’ and ‘off’ automatically.

The unit is not suitable

for special burglary alarm

systems since it lacks

the tampering protection

prescribed for this pur-

1) e.g. 1-4 x 100 W ﬁ lament bulbs

2) Service load, light of 600 W max. (see Technical speciﬁ cations)

3) IS 2160 connection terminals

4) Indoor switch

5) Indoor series switch, manual, automatic

6) Indoor double-throw switch, automatic, permanent light ‘ON’

Wiring examples

2. Light with neutral conductor

1. Light without neutral conductor

4. Connection to double-throw switch

for permanent light ‘ON’ and automatic

operation

Setting I: automatic operation

Setting II: manual operation for permanent

light ‘ON’

Important: the unit cannot be switched

off, but operated only at settings I and II.

3. Connection using series switch

for manual and automatic operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Steinel IS 2160 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info