Bedienungsanleitung Strong SRT 7300 CI plus (Seite 14 von 23) (Englisch)

568532

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

PART 1 • English

English

Scrambled: scan scrambled channels only.

Service Type All: scan TV and Radio channels

TV scan: TV channels only

Radio: scan radio channels only.

Network Search Disabled: no network search

Enabled: network search will be performed.

Once all settings are made, press the GREEN button on the remote control to start the scan or EXIT to

quit without scanning. All newly found channels will be stored at the end of the channel list.

Tip: Network Search: If Disabled is selected, the receiver will search only for

channels available from the preset transponder list of the selected satellite. If

it is set to Enabled, the receiver will perform an additional search for channels

from the NIT table (NIT= Network Identiﬁcation Table). Use this option to

receive new launched channels from the selected satellite.

7.1.3 Manual Scan

Use this menu to scan a single transponder only.

The following can be set: Satellite, Transponder, Frequency, Polarisation, Symbolrate, Scan Mode, Service

Type and Network search. Use pq to move the highlight to the chosen setting and tu to change its

value. Once all settings set correct, press the GREEN button to start scanning or EXIT to quit. All newly

found channels will be stored at the end of the channel list.

Note: Press YELLOW in the Manual Scan menu to make settings for a PID search.

Scan mode, Service type and Network search will then be replaced by settings for

Video PID, Audio PID and PCR PID. For information on PID values, please visit

websites like: www.lyngsat.com or www.kingofsat.net

7.1.4 Satellite Edit

Here you can edit transponder data or add a new satellite.

On the left of the screen, a list with all available satellites is displayed. The right of the screen displays a

list will all available transponders for the highlighted satellite.

Adding or editing a transponder

Use pq to highlight the desired satellite. Press u to move the highlight to the transponder list. Press

YELLOW to add a transponder or use pq to highlight the transponder to be edited and then press

BLUE to enter the edit screen. Use pq to navigate in the edit screen and use tu respectively [0~9] to

change the settings. Once all settings are made, press GREEN to save or EXIT to quit without saving.

Editing an existing satellite

Use pq to highlight the satellite you wish to edit. Press BLUE to go to the Satellite Edit screen. To edit

the name of the satellite, use pq to highlight the name and press OK. A keyboard will pop up. Use pq

tu to navigate and OK to input the chosen character. Once ﬁnished press GREEN to save the changes

or EXIT to quit without saving. To edit the position of the satellite, use pq to move the highlight

to Position and use the [0~9] buttons to input the new position. To change the location, use pq to

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7300 CI plus Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT 7300 CI plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info