Bedienungsanleitung Strong SRT 7300 CI plus (Seite 15 von 23) (Englisch)

568532

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

PART 1 • English

highlight Location and use tu to change the location. Possible settings are: East and West. Once all

settings are made press GREEN to save or EXIT to quit without saving.

Adding a satellite

To add a satellite, make sure the highlight is not in the transponders list (press t in case of doubt) and

press YELLOW. The procedure for adding a satellite is the same as for editing a satellite.

7.2 Setup

Use the Setup menu to conﬁgure the system settings of your receiver. The following sub-menus are

available: Language, Output Options, Time Setting, Parental Control and OSD Display. Choose the desired

submenu with pq and press OK to advance.

7.2.1 Language

Here you can set the preferred Display, Audio and Subtitle languages and Country setting. Use pq to

highlight the setting you wish to change and tu to change the value of the highlighted setting. Press

OK for a list with all available options for the chosen setting.

Display: This setting affects the menu language of your receiver. All menu’s and

messages will be displayed in this language.

Audio: is the preferred audio language. The receiver will automatically switch audio to

the preferred language whenever available.

Subtitle: Whenever available, subtitles will be displayed in the selected language.

Country: Here you can set your country of residence.

Once all settings are made, press EXIT to leave the Language menu. A conﬁrmation banner will be

shown. Press OK to save your settings or EXIT to discard.

7.2.2 Output Options

This is the menu to conﬁgure the audio and video outputs of your receiver. Use pq to highlight the

setting you wish to change and tu to change the value of the highlighted setting. Press OK for a list

with all available options for the chosen setting.

TV Standard: Set the standard corresponding to your TV set. Available options are: Auto,

NTSC, PAL and SECAM.

Aspect Ratio: Use this option to set the aspect ratio of your TV set. Available options are: 4:3

and 16:9.

Conversion mode: Use this option to set the preferred way of converting 16:9 broadcasts to 4:3 TV

format. You can choose between the following options: Letter-box (the full 16:9

picture will be displayed on your 4:3 TV set with black bars above and below the

picture.), Pan and scan (The centre of the 16:9 picture will be displayed full-screen

on your 4:3 TV) and Combined (Combination of Letter-box and Pan and scan.)

SCART Mode: Select RGB for the best picture quality or CVBS in case your TV doesn’t support RGB.

Digital Audio: Deﬁnes the format available on the S/PDIF output of your receiver. When set

to PCM, the digital output will always output PCM stereo regardless of the

broadcasted audio format. The Auto setting will pass all incoming digital audio

through the digital output. Use this option if you have your receiver connected

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7300 CI plus Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong SRT 7300 CI plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info