Bedienungsanleitung Strong srt 7335 hd (Seite 16 von 31) (Englisch)

424893

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

PART 1 • English

English

Lock

Lock function can be used in order to block access to some channels. Press GREEN button to lock/

unlock channel of your choice. Locked channel will be marked by Lock symbol. In order to watch locked

channel you will need to enter PIN code. Channel will be locked in all channel lists.

Delete

Pressing YELLOW button will mark selected channel to delete. To unmark channel select it and press

YELLOW button again. Channel(s) will be deleted after you press BLUE button. Be aware: after pressing

BLUE button channel(s) will be deleted from all channel lists. To cancel delete operation you can press EXIT

button. Message “Do you want to save?” will appear on screen. Press EXIT to cancel or OK to conﬁrm.

5.2 Satellite Search

The Satellite Search menu contains following sub-menus:

Channel set-up allows you to setup channels from selected satellites.

Dish Set-up allows you to setup conﬁguration of your dishes.

Edit satellites allows you to edit predeﬁned satellites and their transponders as well as add new satellites.

GOTO X setup allows you to setup your location in order to use GOTO X type of positioner.

5.2.1 Channel set-up

From this menu you can setup channels from satellite(s) in several modes, access to

Dish setup menu,

Positioner setup (if used).

Satellite:

Move focus of the menu to this item. Press OK to display list of available satellites.

Select satellite of your choice and press OK. If satellite doesn’t exist in the list you

should add it ﬁrst using

Edit satellites menu.

Dish number: move focus of the menu to this item. Use tu buttons to select dish number to which

above selected satellite belongs to. Press OK button to enter to Dish setup menu. Dish

number “----“ means that selected satellite do not belongs to any dish.

Dish position:

This item value depends on the mode of the Dish.

If mode of selected dish is Fixed then this item is not selectable.

If mode of selected dish is DiSEqC 1.2 then value cannot be stored (in case dish

position for selected satellite was not stored) or in range from 1 to 64 if position has

been stored. Select item and press OK to setup positioner. See chapter 5.2.1.1 for more

details about Positioner setup. If mode of selected dish is GOTO X then value is GOTO X.

Select item and press OK to setup GOTO X function.

Transponder: Move focus of the menu to this item and press

OK. List of transponders of selected

satellite will appear at right side of the screen. You can select transponder in order to

check signal strength and quality of reception. Transponder list contains predeﬁned

transponders. If you need to modify transponder list please use menu Edit satellites as

described in chapter 5.2.3. If you need to scan speciﬁc transponder then use Manual

scan as described in this chapter below.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong srt 7335 hd Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong srt 7335 hd

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info