Bedienungsanleitung Strong srt 7335 hd (Seite 18 von 31) (Englisch)

424893

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

PART 1 • English

English

Step by step recommendations of position setup

n Select reference transponder in order to check signal strength and quality during position setup.

n If you do not know current direction of your dish then move menu focus to Centre position

item and press OK. Dish will be turned to true South. Knowing your location longitude you

may understand direction where necessary to move dish in order to reach position of selected

satellite. For example: your longitude is 5° East and you want to setup dish position for ASTRA

1C, 1E (19° East). Then, from centre position, you need to move dish to East direction by

pressing to t button. If your longitude is 25° East then, in order to setup dish position for

ASTRA 1C, 1E (19° East), you need to move dish in West direction (from centre position) by

pressing to u button.

n To setup roughly position of the dish set Movement speed to Fast. Then move menu focus

to Move item of the menu and by short presses to t or u buttons move dish to necessary

direction. Check signal strength and quality indicators. Once levels start increasing – press OK

button to stop the dish. Set Movement speed to Slow and keep adjusting dish position until get

best possible values.

n Once you are sure that dish is ﬁne adjusted press YELLOW (Store) or BLUE (Store & Exit)

button. Dish position for selected satellite will be stored.

NOTE: in order to avoid mechanical damage of your dish please, make sure those mechanical

limits in your motor are set correctly and dish would not hit any objects on its movement.

5.2.2 Dish set-up

In this menu you can setup parameters of your dish(es).

Dish number: Use tu buttons to select number of the dish. This number used in Channel setup

menu to create a link between satellite and corresponded dish conﬁguration

LNB type: Use tu buttons to select type of LNB. If you set type to Universal then you

should enter values of Local Oscillator Frequencies in LO frequencies menu item

LO frequencies: this menu item selectable only in case LNB type is Universal. Press OK button

and using 0 ~ 9 buttons enter values in appeared dialog box.

Band control:

Use tu buttons to select value. Set to Auto in order receiver automatically

select Band by sending 22 kHz control signal. Set to ON in order receiver

generate 22 kHz control signal continuously, or set to

OFF in order to disable

22 kHz control signal.

Polarisation control: Use tu buttons to select value. Set to Auto in order receiver automatically

control polarisation. Set to 13 V or 18 V in order receiver supply LNB with

selected power, or set to

OFF in order to disable LNB power.

Switch type:

if you use DiSEqC switch the select appropriated type.

Switch input: select input number to which LNB is connected.

Dish mode: Use tu buttons to select between Fixed, DiSEqC 1.2 and GOTO X.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong srt 7335 hd Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Strong srt 7335 hd

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info