Bedienungsanleitung Strong SRT 7805 (Seite 13 von 25) (Englisch)

480571

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

PART 2 • English

7.1 Channel Setup

The installation menu allows you to change satellite settings and to search for channels. It consists of

the following sub-menus: Channel Scan and Channel Editor. Choose the desired sub menu with pq and

press OK to advance.

7.1.1 Channel Scan

Use this menu to select the satellite, change the settings for the used antenna and start scan process for

searching the channels.

Satellite: Use pq to highlight Satellite and tu to select the satellite you wish to

change the settings for. To display the list of all available satellites, press OK. At

the end of this list you can ﬁnd Newsat1 -10. Those can be used to conﬁgure a

new satellite setup.

LNB: Select LNB type if you are using another LNB as Univ.LNB model. As this is the

common used LNB, it is set per default.

DiSEqC: If you are using a DiSEqC switch in order to connect more dishes, select the

correct used switch type. Select DiSEqC 1.0 for maximum 4 dishes. DiSEqC 1.1

for maximum 16 dishes and select None if you don’t use any switch.

DiSEqC Port: If you are using a DiSEqC switch you need to set the correct DiSEqC port which

belongs to the connected satellite.

Transponder: Select this option, if you want to scan manually or check the signal on the

desired transponder frequency. Use tu to select the transponder of you

choice, or open the Transponder list of the selected satellite with OK.

Motor Control: If you are using a DiSEqC motor to install multiple satellites. Select the

according setup type withtu. Select DiSEqC 1.2 for manual setup of each

satellite or select GOTO-X for automatic calculation after you have adjusted the

0-position and corresponding Cartesian coordinates of your location.

Note: Please consider that GOTO X must be supported from your Motor as well!

Motor Setting: Here you can setup the necessary settings according to the used Motor

Control. Adjust and store these settings correctly, in order to be able to proceed

with Search Start.

Search Start:

Before you start the scan process please make sure that all settings are made correctly and Strength and

Quality bars are showing green colours. If the Strength and Quality bars showing red or yellow colours,

then the satellite signal is too weak. Please try to adjust your satellite dish ﬁrst, to improve the signal.

At the ﬁrst time installation there was performed the HD+ Channel Scan from APS. After this successful

scan process you can choose following of the additional possibilities:

Select Search Start and press OK.

A new menu will be opened on the right side of your screen, called “Options”. Use this menu to perform

an Automatic, TP (manual) or Network channel search on one or more satellites. Use tu pq to

highlight and OK to select an option.

Start Auto Scan: Use this option to perform a full channel scan on the selected satellite, under

the below mentioned conditions.

TP Search Start: Use this option to perform a scan on the selected transponder only.

Network Search Start: Use this option to receive new launched channels from the selected satellite.

The receiver will perform an additional search for channels from the NIT table

(NIT= Network Identiﬁcation Table).

Search Mode: Select All to scan all channels including scrambled channels or FTA to scan for

Free-To-Air channels only.

NIT Search: Select OFF if you don’t want to perform a network search or set ON to perform

a network search.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Strong SRT 7805 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info