587254
24
Zoom out
Zoom in
Vorherige Seite
1/48
Nächste Seite
24
TASCAM CD-200SB
4 – Playback
Folder playback (data CDs/SD cards/
USB flash drives)
With data CDs, SD cards and USB flash drives, you can set the
selected folder (current folder) as the playback area. Follow the
procedures below to set the playback folder. You can also set the
playback area to be all the tracks/files on the current media by
selecting
ALL PLAY
.
Setting the playback folder
1. While pressing and holding the main unit DISPLAY [SHIFT]
button, press the PLAY MODE/INTRO CHECK [PLAY AREA]
button (or press the remote PLAY AREA button) to set the
playback area to
FOLDER
.
2. Use the main unit FOLDER g/t [PITCH −/+, / ] buttons
or the remote FOLDER g/t [ / ] buttons to skip to the
previous or next folder.
This will skip to the beginning of the first track in the
previous or next folder. If you hold down one of these
buttons, you can skip through folders continuously in order.
NOTE
When you skip to a different folder, it becomes the current
folder.
During folder playback, repeat playback will play back all
tracks inside the current folder repeatedly.
During folder playback, random playback will play back all
tracks inside the current folder randomly.
Programmed playback
To use programmed playback, you must set a program either
before or after setting the playback mode to programmed
playback mode. (See “Selecting the playback mode on page
22.)
When in programmed playback mode, press the PLAY/PAUSE
button on the main unit or the remote control to start playback
of the set program in order from the first track (program step
01).
Press the main unit SEARCH m/, [.//, SELECT 5/
b] button or the remote search (m/. [SELECT 5] or
//, [SELECT b]) button to skip to the previous or next
program step.
When playback is stopped in program playback mode using an
audio CD, the total number of tracks in the program and the
total program time are shown.
When using a data CD, only the program number is shown.
When using an SD card or USB flash drive, the number and time
of the track being played back are shown.
NOTE
To select programmed playback, when stopped, press the
main unit PLAY MODE/INTRO CHECK [PLAY AREA] button
or the remote PLAY MODE button.
When using a data CD, SD card or USB flash drive, you
cannot set a program when the playback area is
ALL PLAY
.
Change the playback area to
FOLDER
to enable tracks in the
current folder to be used in the program.
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam CD-200SB wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info