161727
21
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
1-Introduction
TASCAM CD-RW900 21
5−Recording
The sampling frequency for CDs is 44.1 kHz. The CD-
RW900 will always record (and play back) CDs at this
frequency.
However, if recording through a digital connection
(either coaxial or optical) and the source has been re-
corded at a frequency other than 44.1 kHz, or is being
played back at a non-standard speed using a varispeed
unit (more than 1% away from the standard), the CD-
RW900s internal frequency converter: SRC (Sampling
rate convertor) will automatically convert the incoming
frequency to 44.1 kHz.
To set the SRC
Press the MENU key and select the SRC? option in
the REC sub-menu (refer to “Operation basicson
page 14).
Rotate the MULTI JOG dial and select ON.
Press the MENU key or push the MULTI JOG dial to
enter and return to normal mode.
NOTE
When the SRC function is off, receiving digital signals,
the display shows the REC indicator ashing while re-
cording or recording standby mode.
The digital signals other than 44.1kHz cannot be re-
corded when SRC is off. The error message
Not
Fs44.1k!
will appear on the display.
Frequency conversion
Before you start recording using the CD-RW900, make
sure that you understand the following key points:
Once you have recorded on a CD-R disc, the data
cannot be erased from it.
You can add tracks to an unnalized recordable
disc. Once nalized, a CD-R disc is xed and
behaves in the same way as a pre-recorded disc.
Finalized CD-RW discs, however, can be erased, re-
freshed and re-recorded.
Input selection
To select the input to be recorded, press the INPUT
SELECT key on the main unit.
Repeated presses of the key cycle through the follow-
ing options:
ANALOG Analog
OPTICAL Optical digital in
COAXIAL Coaxial digital in
In the case of either the coaxial or optical inputs being
selected, the appropriate indicator:
COAXIAL
or
OPTI-
CAL
, lights on the right of the screen.
If the analog signal is selected, the
ANALOG
indicator
lights on the right of the screen.
Analog recording level The level of the analog signals
received at the ANALOG IN jacks are controlled with
the INPUT controls.
When recording analog signals, set the digital volume to
0 dB.
Digital recording level The level of the digital signal
may be controlled using the digital volume menu, as de-
scribed below.
1 Call up the
VOLUME
option in the REC sub-menu
(refer to “Operation basics” on page 14).
Push the MULTI JOG dial to enter the function on.
2 Rotate the MULTI JOG dial to adjust the input vol-
ume between -54dB and +18 dB (relative to the
original input level).
There is also a -
setting which represents a com-
plete signal cut. The display shows
Vol> ---dB
for
the -
setting.
3 Press the MENU key or push the MULTI JOG dial to
enter the setting and return to normal mode.
Input monitoring
When the unit is in record ready, or record mode, the
input signal is output from the OUT jacks (digital and
analog), allowing you to hear the input signal.
1 Press the RECORD key on the front panel or the re-
mote control when a recordable disc is not inserted.
The word
Monitor
appears on the display to show
that the output signal is an echo of the input signal(s).
2 Exit the monitor mode by using the STOP key.
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tascam cdrw900 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info