Bedienungsanleitung Tascam cdrw900 (Seite 22 von 32) (Englisch)

161727

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1-Introduction

22 TASCAM CD-RW900

5−Recording

Basic recording

1 Load a recordable disc into the unit. As the disc

loaded, the display shows

TOC Reading.

, with the

period ashing.

2 Press the INPUT SELECT key to select a recording

source (see “Input selection” on page 21).

If a digital source is selected, and the connection or

the signal are improper, the error message

D-IN UN-

LOCK!

will appear on the display.

3 Press the RECORD key. The unit enters record

ready mode, as shown by the

REC

and

READY

indi-

cators on the display.

NOTE

As the unit enters record ready mode, the display

shows the

Now OPC

(Optimum Power Control) occa-

sionally, as the unit prepares to record on the disc.

To adjust the level of the source, following the guide-

lines in “Input selection” on page 21.

NOTE

The red

OVER

indicators on the meters should never

light. Unlike analog equipment, digital audio units pro-

duce extremely unpleasant sounds when distorted, and

there is no “headroom” after the 0 mark. If recording

digitally from a commercially-produced CD, the volume

set in the menu should be 0 dB. This will maintain all the

dynamic range of the source CD without clipping. Only

boost the signal if the source is exceptionally quiet.

An analog signal input at nominal level, with no cut or

boost from the volume controls, is equivalent to a read-

ing of −16 dB on the meters.

4 Press the PLAY key to start recording.

Pressing the READY key stands by recording tem-

porarily. To restart recording, press the READY key

or PLAY key again.

5 Press the STOP key to stop recording.

When recording stops, the display shows

PMA

Writing

(Program Memory Area) ashing for a few

seconds as the unit writes to the disc.

NOTE

≠

During the

PMA Writing

is shown, any key cannot

be used.

≠

To conrm the total recording time, use the REC

TIME opyion in the SYSTEM sub-menu (refer to “Op-

eration basics” on page 14).

CAUTION

Do not vibrate the unit or turn off the power when the

unit writes to the disc, otherwise, recording fails.

When in record or record ready mode, repeated press-

es of the TIME key cycle through four different time

modes:

≠

Elapsed track time (no display light indication)

≠

Remaining track time (

REMAIN

is lit in the display)

≠

Elapsed disc time (

TOTAL

is lit in the display)

≠

Remaining disc time (

TOTAL

and

REMAIN

are lit in

the display)

Time display while recording

Full disc

If recording a long program, when there is no space

remaining on the disc for recording, as shown by the

above time display, just before the end of the disc is

reached, the unit starts a fade-out over four seconds

(the display shows

Fade Out

When the fade-out has nished, the display shows

Disc

Full!

. Press the STOP key to exit.

If the disc is a CD-RW, the nal track can be erased, if

required (see “Erasing” on page 26) and the disc then

nalized. If the disc is a CD-R, it must be nalized prior

to use (see “Finalizing” on page 25).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam cdrw900 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info