Bedienungsanleitung Tascam cdrw900 (Seite 23 von 32) (Englisch)

161727

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

1-Introduction

TASCAM CD-RW900 23

5−Recording

Advanced recording

Fade-in and fade-out recording

At the beginning and end of recording, fade-in and

fade-out effects can be performed.

1 During stop or recording standby mode, set the op-

eration using the following menu options on the REC

sub-menu (refer to “Operation basics” on page 14).

FADE IN?

The length of the fade in to the normal level can be

set between 1 and 30 seconds in 1-second incre-

ments (default setting: 3 seconds).

FADE OUT?

The length of the fade out into complete silence

can be set between 1 and 30 seconds in 1-second

incre-ments (default setting: 3 seconds).

The display shows

Fade Out>XXs

Fade In>XXs

2 In recording standby mode, press the FADER key

on the remote control.

Recording begins and the sound fades in. After the

preset fade-in time, the sound is at normal level.

3 During recording, press the FADER key on the re-

mote control when you wish to fade-out the sound.

Fade-out begins with

Fade Out

ashing on the dis-

play then the unit enters recording standby mode.

4 Press the STOP key and the PMA writing will begin.

NOTE

Fade-in or fade-out function can be operated only

pressing the FADER key on the remote control unit.

Synchronized recording basically means that recording

will begin automatically when a signal is received, and

will stop when the signal ends.

Use the SYNC REC key to select the synchronization

mode. The synchronization mode determines the auto-

mated start and stopping of recording when a signal is

received.

During stop or recording stancby mode, repeated

presses of this key cycle through the fol-lowing modes:

≠

Sync ALL: The

SYNC

indicator lights up.

≠

Sync 1: The unit stops when a selected track is n-

ished and the

SYNC

indicator ashes

≠

Sync OFF: Turns Sync recording function off

After the synchronization mode is selected, the record

ready mode must then be entered (you cannot reverse

the order of these steps).

Starting playback of the source automatically starts re-

cording on the CD-RW900 if Sync ALL or Sync 1 has

been selected (see “Sync recording” below) and manual

record start is disabled. If Sync OFF is selected, the re-

cording must be started manually.

Synchronaized recording

Sync recording

1 While recording standby mode, press the SYNC

REC key repeatedly to select Sync ALL or Sync 1.

2 Set the signal detection threshold level. Use the

SYNC LEVEL option in the REC sub-menu (refer to

“Operation basics” on page 14).

Rotate the MULTI JOG dial to adjust the level. The

level can be set from -72 dB to -24 dB in 6 dB incre-

ments. The default setting is -24 dB.

Press the MENU key or push the MULTI JOG dial to

enter and return to recording standby mode.

3 Input the source signal.

Recording begins automatically when the source

signal is detected. The source signal should be high-

er than the adjusted threshold level.

NOTE

≠

After the mode is set, more than one second of

signal under the adjusted threshold level is required

to start recording automatically, otherwise, the unit

does not begin recording even it detects the signals.

S_LVL

Start of recording

level

time

Noise level

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam cdrw900 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info