Bedienungsanleitung Tascam DP-02CF (Seite 34 von 80) (Englisch)

617899

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

IMPORTANT SAFETY PRECAUTIONS

34 TASCAM DP-02/DP-02CF

2 – Advanced techniques

Repeat allows you to repeat the playback or auto-punched

rehearsal (see “Rehearsal” on page 32) between the IN and

OUT points.

First, set the IN and OUT points at the place where you

want the repeat loop to start and stop (see “IN and OUT

marks” on page 30).

NOTE

You can’t set these points when the REPEAT key is lit.

Press the REPEAT key briefly so that the indicator lights.

Playback starts automatically from the IN point.

When the playback reaches the OUT point, playback

pauses for a short while (see “Setting the repeat interval”

on page 35) and the PLAY (¥) indicator flashes before

playback starts again, and the PLAY (¥) indicator lights

steadily.

Turn off the repeat function by pressing REPEAT so that

the indicator goes out.

Repeat auto-punch rehearsal, but not repeat auto-punch

recording, is also possible. If AUTO PUNCH, RHSL and

REPEAT are all lit, pressing RHSL to go from rehearsal to

auto punch recording mode will also turn off REPEAT.

Repeat

Bouncing

“Bouncing” on the unit refers to the technique of mixing

recorded tracks through the MASTER fader to a pair of

unused tracks.

You might use a track bounce operation in the following

situation:

T I P

You can bounce to one track, if you want, but you will

probably want to bounce in stereo.

1 Drums L

2 Drums R

3 Bass

4 Acoustic Guitar

5 E. Guitar 1

6 E. Guitar 2

1 Organ L

2 Organ R

3 Lead vox 1

4 Lead vox 2

5 Backing vox 1

6 Backing vox 2

7 Bounce mix L

8 Bounce mix R

MASTER(stereo)

You’ve recorded the drums in stereo, the bass and two

rhythm guitars (one acoustic and one electric) and an elec-

tric guitar lead line. There are two tracks left. You’d like

some stereo organ added in, and there are two lead vocal

lines to record, as well as at least one set of backing vocals.

But there are only two tracks left!

Luckily, you can bounce everything through the stereo

tracks, and record them onto the two spare tracks.

1. “Un-arm” (safe) the existing tracks so that you don’

t accidentally record over them.

T I P

You may want to copy the song and give it another

name (see “Copying songs” on page 41) before start-

ing the bounce, so that you can go back to the original

if necessary.

2. Press the BOUNCE key (above the MASTER fader)

so that it lights.

3. Arm the two tracks which you are mixing to.

4. Use the faders and mixer controls of the tracks you’

re bouncing to create a stereo mix.

5. Adjust the overall level of the mix using the

MASTER fader. Watch the L and R meters on the

right side of the display so that the level is adjusted

to the optimum level. During this step, mute the

tracks at the bounce destination.

6. When you’re ready, use PLAY (¥) and RECORD (–

) to record the mix onto the two armed tracks from

start to end, with no stops. “Safe” the armed tracks.

You can now record over the original tracks you bounced,

playing along to the stereo pair created from the bounce.

T I P

You can also use auto punch recording (“Punching” on

page 32) to bounce only part of a song between the IN

and OUT points.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tascam DP-02CF Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tascam DP-02CF

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info