Bedienungsanleitung Team TeCom-IP3 (Seite 12 von 27) (Deutsch, Englisch, Italienisch, Spanisch)

749145

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

22 23

English BASIC FUNCTIONS

Antenna

In the PMR version, due to governmental regulations, the

antenna is fixed, i.e. non-detachable.

Battery Pack

To attach the battery pack (11), place the battery pack onto the radio and press the

bottom part close to the radio case and close the lock.

Charging

Prior to first use, the battery pack has to be charged completely. A completely

empty battery pack needs to be charged for approximately three hours. During the

charging process, the LED lights red. Once charging is completed, the LED lights

green.

Remove the battery pack out of the charger. Overcharging reduces the battery

packs longevity.

On / Off

To turn the radio on, turn the On / Off switch (2) clockwise beyond the barrier. A

beep tone is emitted if the beep tone function is activated.

To turn off the radio, please turn the On / Off switch (2) counterclockwise beyond

the barrier.

Volume Control

To set a comfortable volume level after turning the radio on, activate the monitor

function by pressing the according multi-functional key PF1/2 (9) (which has to be

programmed via software) while adjusting the volume level with the combined

On/Off-Volume key (2).

Channel Selection

For channel selection, use the rotary channel selector (3) switch.

The channels are selected in the programmed order.

English

Transmit

For transmission hold the PTT key (8) until the end of the message.

For best sound quality, talk into the microphone (4) with normal voice at a distance

of approximatly 10 cm.

During transmission the control LED (6) lights red.

Upon release of the PTT key (8) the radio returns automatically into reception mode.

Reception

Upon reception of a signal, the LED (6) lights green.

If the selected frequency is decoded with a CTCSS- / DCS-code, all signals that

are encoded with a different code will be muted. The green LED will light but no

signal will be audible.

KEY FUNCTIONS

PTT Key

The PTT key (8) is located at the left side of the radio. Pressing the PTT key will

switch the radio into transmission mode. The LED (6) will light red.

Multi-Function Keys

The multi function keys PF1 and PF2 (9) are located below the PTT key (8). Each of

them are programmable via the software T-UP31 with two of the following functions

that are activated by pressing short or long:

Monitor Scan VOX

Priority Scan Revert Frequency

Offline Power (Low/High)

monitor

The monitor functions remains active until the key is pressed again.

scan

Start / stop the channel scan function by pressing the key. Each channel can be

added to or deleted from the scan list by software programming.

This function is only available if at least two channels are added to the scan list.

tecom-ip3_man_V5_18-2-14_Layout 1 14.02.2018 10:37 Seite 22

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Team TeCom-IP3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info