Bedienungsanleitung Telair Energy 2510b (Seite 20 von 40) (Englisch)

688849

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Energy 2510 B

Vers. 002

has inexplicable behavior or the display shows

characters without any logic).

6.6 Control panel alarm causes and resetting

During generating set use, alarm signals may be

displayed referring to engine oil checks. After

checking the engine oil, the control panel must

be reset in the following way:

Alarm: the red ‘service’ light is flashing.

Cause: 50 hours have elapsed since the latest

engine oil change and oil level should be

checked.

How to reset the alarm: with panel turned off,

press the partial counter key (Fig.30 Ref.9) and

while holding it down, turn the panel on and re-

lease the push-button when the unit has started

Alarm: the red ‘service’ light is lit.

Cause: 100 hours have elapsed since the latest

engine oil change and engine oil should be

changed.

How to reset the alarm: turn on the panel and

wait for the generating set to start. Now press the

button hidden under the small hole in the bottom

left corner (Fig.30 Ref.10) and release it immedi-

ately thereafter. Wait a couple of minutes before

turning the generating set off.

Alarm: the display unit shows random charac-

ters.

Cause: malfunctioning due to low voltage during

start-up (low battery, cable cross-section too

small). In this case, just turn Off and On the con-

trol panel.

In certain situations, data of internal microproc-

essor of the panel may be subject to permanent

alterations and prevent running of generating set.

In this case, to restore the functionality of panel is

necessary to completely re-initialize (contact the

Service).

6.7 Automatic Version (optional)

If you wish the start-up batteries to be recharged

automatically in the En 2510 B generating sets, it

is possible to install the ASP (optional) automatic

control panel (fig.32) instead of the manual con-

trol panel.

The elements making it up are:

1 ON/OFF switch for the start-up and switch-off

function

2 Display

3 High temperature indicator

4 Minimum oil level indicator

5 Start-up failed indicator

6 Generator running indicator (flashing)

7 Maintenance request indicator

8 Fuel reserve indicator

9 Hour or voltmetric changeover switch button

10 Reset

11 Battery charged indicator

12 Automatic function indicator

13 AUTO/MAN switch for the automatic or man-

ual function

6.8 MANUAL operation

See section 6.1

6.9 AUTOMATIC operation

Turn the AUTO/MAN switch (Fig.32 Ref.13) to

the AUTO position and set the start-up switch

(Fig. 32 Ref. 1) to ON position.

The automatic function indicator (Fig.32 Ref.12)

will light up.

When the voltage at the ends of the 12V DC ter-

minals of the generating set is lower than 11.5

Volts, the generating set will begin the start-up

procedure (similar to that of the manual opera-

tion).

During the operation in automatic mode, the dis-

play (Fig.32 Ref.2) will show the total running

hours of the generating set. Press the hour or

voltmetric changeover switch button (Fig.32

Ref.9) to display the voltage at the ends of the

12V DC terminals, i.e. at the ends of the battery.

When the battery is charged, and anyway after at

least 15 minutes’ running, the battery charged

hours indicator (Fig.32 Ref.11) will light up and

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telair Energy 2510b Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info