Bedienungsanleitung Thomson THS221 (Seite 17 von 34) (Englisch)

658774

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

MAIN MENU

P13

English

7.1.2 Configure the antenna settings for the selected satellite

Satellite The name of the selected satellite is shown here.

LNB The setting is Universal LNB (09750/10600) – the most used on the market.

Transponder Select a transponder, known to carry a signal.

DiSEqC 1.0 Select the switch type in use. 4to1(DiSEqC 1.0) or 16to1. (DiSEqC 1.1)

Select Tone Burst if a Legacy 2to1 switch is used.

Uncommitted If uncommitted DiSEqC switches are used, select them here. (Advanced

user setup)

22K Tone Auto: this setting will follow automatically.

Polarity 13/18 V, this setting will follow automatically.

Motor If using a motor, press tu to choose DiSEqC1.2/GOTOX. Then press OK to

show the menu for setting the position for your location.

DiSEqC1.2 Move the motor to the right position for locking the signal like explained

below.

Move Continue: press tu for moving West/East. It will keep moving as

long as the button is kept pressed. By pressing once it will move in 1° step.

Move Step(1): press tu for moving West/East in 0.3° step.

Store Position: to store the current motor position for selected satellite.

Goto Reference: to go to the reference 0° position.

GOTO X Select GOTO X with the tu buttons. Press GREEN to setup your location

coordinates. A pop-up window will appear, in which the following settings

can be made:

Location: Press tu to select one of the pre-set locations. Choose a location nearest

to you. If you know the coordinates of your place of residence, you can

choose Manual and make the following extra adjustments:

Longitude Direction: Choose East or West.

Longitude Angle: Press the 0~9 buttons to enter the coordinate.

Latitude Direction: Choose North or South.

Latitude Angle: Press the 0~9 buttons to enter the coordinate. When all settings have

been made, press EXIT to save the data and leave the window. Now

press OK to enter the GOTO X menu. Move Auto will move the dish to the

selected satellite automatically. For Move Continue, Move Step (1) and Goto

Reference please see explanation above.

SatCR Select On, if you use a SatCR LNB, otherwise leave to Off. When On is

selected press YELLOW (Setup SatCR) to enter the Sat setup page.

Position: Select the LNB A or LNB B.

IF Channel: Select the IF channel number according to the specifications of your

SatCR LNB. Note: Any SatCR LNB in the chain needs a different IF channel

number.

Center Frequency: Select the Center Frequency according to the specifications of your SatCR

LNB. Note: Any SatCR LNB in the chain needs a different Center Frequency.

Select the store button to nalize your settings or press MENU or EXIT to leave without storing.

7.1.3 Satellite and Transponder edit options

When in Satellite Setting use the RED TP Edit button to edit Satellites and Transponders.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson THS221 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson THS221

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info