Bedienungsanleitung Thomson THS221 (Seite 19 von 34) (Englisch)

658774

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

MAIN MENU

P15

English

NIT: Network Information Table. If selected On, the receiver will use the NIT

provided by the satellite provider to search for channels. If selected Off, the

receiver will search with its pre-installed transponder list.

Programme: Select Free Only to search for Free to Air channels. Select All to include

scrambled channels as well. Note: Scrambled channels cannot be watched

with this receiver.

Scan Mode: Default TP: All stored transponders in the memory will be scanned.

Blind: Slow scan in 2 MHz steps. The receiver will first scan the whole

frequency band to find the transponders it can lock on. After gathering

all transponders, it scans the transponders one by one to get all available

programmes.

One TP: The transponder selected under Transponder will only be scanned.

Scan Select: Select All Sat to search all satellites you have selected in the Satellite Setting

menu. Select Single Sat to search only the satellite selected under Satellite.

After conguring, press GREEN to start scanning with the selected settings.

Your receiver will now perform an automatic channel search with the scanning progress shown

on screen. During the channel search you can quit the scan process with EXIT or MENU. When the

progress has been completed, all found channels will be stored and the receiver will switch to the

rst found channel.

7.1.5 Manual scan - Scanning by transponder

Select the options if you want to do a manual scan. (Advanced users.)

Satellite: Select the satellite you wish to scan from, as previously set up in the

Satellite Setting menu.

Frequency: Enter a known frequency of a satellite transponder with the 0~9 buttons

on the remote.

Symbol Rate: Enter the symbol rate of the previously set satellite transponder with the

0~9 buttons on the remote.

Polarity: Set the polarization of the previously set satellite transponder, V (Vertical)

or H (Horizontal).

NIT: Select On if you want to do a scan starting from the previously set satellite

transponder according to the Network Information Table, as offered by the

Satellite Provider. Select Off, to scan just the one transponder.

Programme: Select Free Only to search for Free to Air channels. Select All to include

scrambled channels as well. Note: Scrambled channels cannot be watched

with this receiver.

After conguring, press GREEN to start scanning with the selected settings.

Your receiver will now perform a channel search with the scanning progress shown on screen.

During the channel search you can quit the scan process by pressing EXIT or MENU. When the

progress has been completed, all found channels will be stored and the receiver will switch to

channel number 1. The new found channels are added to the end of the list.

Satellite Finder: You can use the menus Satellite Setting, Automatic Sat Scan or Manual

Scan to find a satellite and peak the dish for maximum reception. Select

the satellite you wish to find or peak, select the settings according to your

dish-setup and then select a transponder which is known to carry a signal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thomson THS221 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson THS221

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info