Bedienungsanleitung Toolson DKS1600 (Seite 24 von 240) (Alle Sprachen)

782195

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

24 GB

10. Cleaning, maintenance, storage

and ordering of spare parts

Important.

Always pull out the power plug before starting any

cleaning work.

10.1 Cleaning

• Keep all safety devices, air vents and the motor

housing free of dirt and dust as far as possible.

• We recommend that you clean the equipment im-

mediately after you use it.

• Wipe the equipment with a clean cloth or blow it

down with compressed air at low pressure.

• Clean the equipment regularly with a damp cloth

and some soft soap. Do not use cleaning agents

or solvents; these may be aggressive to the plastic

parts in the equipment. Ensure that no water can

get into the interior of the equipment.

10.2 Servicing

There are no parts inside the equipment which re-

quire additional maintenance.

10.2.1 Bearing(s) (Fig. 1/Item 8)

Periodically lubricate the bearings (8) of the guide

rollers with high-grade machine grease, at the latest

however after 25 to 30 hours of operation.

10.2.2 Carbon brushes

In case of excessive sparking, have the carbon

brushes checked only by a qualied electrician. Im-

portant: The carbon brushes should not be replaced

by anyone but a qualied electrician.

10.3 Storage

Store the equipment and accessories out of children’s

reach in a dark and dry place at above freezing tem-

perature. The ideal storage temperature is between 5

and 30 °C. Store the electric tool in its original pack-

aging.

10.4 Ordering replacement parts

The following information must be provided on all or-

ders for spare parts:

• Model/type of the equipment

• Article number of the equipment

Service information

Please note that the following parts of this product

are subject to normal or natural wear and that the fol-

lowing parts are therefore also required for use as

consumables.

Wear parts*: Carbon brush, saw blade, table liners,

V-belts

* Not necessarily included in the scope of delivery!

8.6 Miter cutting

To carry out miter cuts adjust the distance of the

blade guard for worktable accordingly. Swivel the

saw table by loosening the locking lever (12) and tilt-

ing the table to the desired position (Fig. 12). Tighten

the locking lever.

Important.

Be especially careful when making miter cuts. The

angle of the saw table makes it easier for the work-

piece to slip. Risk of injury.

9. Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the ex-

tension cable used must also comply with these regu-

lations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking H 05 VV-F.

The printing of the type designation on the connec-

tion cable is mandatory.

AC motor

• The mains voltage must be 220-240 V~

• Extension cables up to 25 m long must have a

cross-section of 1.5 mm2.

Connections and repairs of electrical equipment may

only be carried out by an electrician. Please provide

the following information in the event of any enquiries:

• Type of current for the motor

• Machine data - type plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson DKS1600 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info