Bedienungsanleitung Toolson DKS1600 (Seite 23 von 240) (Alle Sprachen)

782195

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

23GB

Inserting the saw blade without pins (optional)

(Fig. 1+9+9.1+9.2+9.3+9.4)

The teeth of the saw blade must always point down-

wards.

• Put the saw-blade with the two adapters (19/23)

into the lower support, the other end into the up-

per support.

• Slightly push down the outrigger (10).

• Tighten the saw blade (17) with the clamping lever

(9) by pressing it down again. Check the tension

of the saw blade (17). If the tension is insufcient,

it can be increased by turning the lever clockwise.

First release the clamping lever (9).

• Put the table insert (26) back.

Removing the saw blade with pins

(Fig. 1+10+10.1+10.2+10.3)

• To remove the saw blade (17), lift the table insert

(26) upwards.

• First release the tension by lifting the clamping le-

ver (9) upwards. If required, further reduce the ten-

sion by turning it anti-clockwise.

• Slightly push down the outrigger (10) (see Fig. 9).

• Pull the saw blade from the upper and lower saw

blade mounting (24/25)

Inserting the saw blade with pins (Fig.

1+10+10.1+10.2+10.3)

The teeth of the saw blade must always point down-

wards.

• Push one end of the saw blade (17) through the

hole in the table, and guide the pins of the saw

blade (17) into the corresponding slots in the upper

and lower saw blade mounting (24/25).

• First insert the saw blade (17), in the lower blade

holder (25).

• Slightly push down the outrigger (10).

• Check the position of the saw blade pins in the saw

blade mountings (24/25).

• Tighten the saw blade (17) with the clamping lever

(9) by pressing it down again. Check the tension

of the saw blade (17). If the tension is insufcient,

it can be increased by turning the lever clockwise.

First release the clamping lever (9).

• Put the table insert (26) back.

7.3.3 Calibrating the angle scale

Important: Check the adjustment of the angular scale

before you start working with the unit. The angle scale

is already properly set when delivered. Align the saw

table using a 90° stop angle (21) (Not supplied) on the

table and at the saw blade(Fig. 11). Slacken the screw

(28) and turn the pointer (27) to the 90° mark.

Carry out a test run for precise machining: Test the

angle set by making a sample cut and checking the

respective number of degrees on the workpiece using

an angle gage. Readjust the pointer (27) if necessary.

8. Operation

8.1 Note:

• The saw does not cut wood automatically. Rather,

the operator must push and guide the wood toward

the moving saw blade.

• The teeth only cut the wood on the downstroke.

• The wood must be slowly pushed and guided to-

ward the saw blade, since the teeth of the blade

are very small.

• Those who want to use the saw must go through

the process of learning how to do so. During this

time, a few blades will invariably break.

• When cutting thicker wood, special attention must

be paid not to bend or twist the saw blade.

• Handling the saw blade properly increases its ser-

vice life.

8.2 ON/OFF switch (Fig. 2/Item 14)

• Press the “I” button to switch on.

• Press the “0” button to switch off.

Important: The machine is equipped with a safety

switch to prevent it from being switched on again ac-

cidentally after a power failure.

If the mains power supply is interrupted when the fret-

saw is switched on, the saw will switch off and remain

in this state, even after the power is restored. Press

the “I” switch again to switch the saw back on.

8.3 Operating working lamp

• Turn off the machine as described under 8.2

• Now the work lamp (30) can turn ON or OFF by

useing the switch (31).

8.4 Speed regulator (Fig. 2/Item 15)

The speed regulator (15) allows you to set the blade

speed appropriate to the material to be cut. We rec-

ommend high speeds for soft material and low speeds

for hard material. Turning the speed regulator (15) to

the right increases rotational speed.

8.5 Inside cutting

One of the features of this fretsaw is that it can make

cuts inside a panel without damaging the outside or

edges.

To cut inside a panel:

• Remove the saw blade as described in section

7.3. 2.

• Drill a hole in the panel in question.

• Lay the panel with the hole over the access hole in

the saw table.

• Insert the saw blade through the hole in the panel

and set the blade tension.

• When you have nished cutting, remove the saw

blade from the blade holders (as described in sec-

tion 7.3.2) and lift the panel off the table.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson DKS1600 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info