Bedienungsanleitung Toolson DKS1600 (Seite 22 von 240) (Alle Sprachen)

782195

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

22 GB

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Sound pressure level LpA:66,9 dB(A)

Uncertainty KpA:3 dB(A)

Sound power level LWA:79,9 dB(A)

Uncertainty KWA: 3 dB(A)

The quoted values are emission values and not nec-

essarily reliable workplace values. Although there is

a correlation between emission and immission levels

it is impossible to draw any certain conclusions as

to the need for additional precautions. Factors with

a potential inuence on the actual immission level

at the workplace include the duration of impact, the

type of room, and other sources of noise etc., e.g.

the number of machines and other neighboring op-

erations. Reliable workplace values may also vary

from country to country. With this information the user

should at least be able to make a better assessment

of the dangers and risks involved.

Reduce noise generation and vibration to a minimum!

• Use only equipment that is in perfect condition.

• Maintain and clean the equipment regularly.

• Adopt your way of working to the equipment.

• Do not overload the equipment.

• Have the equipment checked if necessary.

• Switch off the equipment when not in use.

7. Before starting the machine

Important:

Always pull out the power plug before making adjust-

ments to the equipment.

7.1 General information

• All covers and safety devices have to be properly

tted before the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed

before, watch out for foreign bodies such as nails

or screws, etc.

• Before you actuate the On/Off switch, make sure

that the saw blade is correctly tted and that the

equipment’s moving parts run smoothly.

• Check that the voltage on the rating plate is the

same as your supply voltage before you connect

the equipment to the power supply.

• Only ever connect the equipment to a properly in-

stalled shock-proof socket which is protected by a

10A fuse as a minimum.

7.2 Installing the fretsaw on a workbench (Fig. 3, 4)

The unit may only be installed by a professional.

Required for installing (not provided):

• M6 hex screw (4x)

• M6 hex nut (8x)

• Washer, Ø 7 mm (4x)

• Flat gasket, Ø 7 mm (4x)

• Rubber base: 410 x 255 x 13 mm

The length of the screws to be used varies, depend-

ing on the thickness of the table top.

• Install the fretsaw on a work table made from solid

wood. This will avoid excessive noise caused by vi-

brations.

• Mark the drill holes. Use the fretsaw as a template

for this purpose.

• Drill 4 holes with a diameter of 9 mm into the work

table and the rubber base.

• Screw the fretsaw to the table using the mount-

ing points (Fig. 3 Item 16) and in the following se-

quence (Fig. 4):

A) Fretsaw

B) Rubber base

C) Work table

D) Flat gasket

E) Washer

F) Hex nut

G) Hex nut

H) Hex screw

• Tighten the hex nut (F) and secure it with a second

hex nut (G).

7.3 Assembly

Important! Always pull out the power plug before car-

rying out any maintenance or conversion work on the

fretsaw.

7.3.1 Mounting the saw blade guard and the saw-

dust blower facility (Fig. 6/7/8)

• Attention: Prior to the installation of the retaining

device (18), the pre-assembled saw blade (17) must

be dismantled as described in articel 7.3.2.

• Secure the retaining device (29) to the machine by

using the knurled screw (3). Attach the retaining de-

vice (18) to the bracket (29), as shown in the gure.

• Secure the saw blade guard (5) with the nut and

bolt.

• Mount the blow-off device (1) as shown in Figure 8.

7.3.2 Changing the saw blade (Fig. 1/9/10)

Important

To avoid injuries attributed to inadvertent startup: Al-

ways move the switch to the “0” position and pull the

power plug out of the socket outlet before removing or

changing the saw blade.

Removing the saw blade without pins (optional)

(Fig. 1+9+9.1+9.2+9.3+9.4)

Use the adapter (19/23) with at saw-blades.

The distance results by the setting gauge (32).

The saw-blade is xed with Allen screws.

• To remove the saw blade (17), lift the table insert

(26) upwards.

• First release the tension by lifting the clamping le-

ver (9) upwards. If required, further reduce the ten-

sion by turning it anti-clockwise.

• Slightly push down the outrigger (10).

• Then remove the sawblade by pulling it forward

out of the supports and through the access perfo-

ration in the table.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson DKS1600 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info