Bedienungsanleitung Toolson DKS1600 (Seite 20 von 240) (Alle Sprachen)

782195

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

20 GB

• Before switching on, make sure that all keys and

wrenches have been removed from the tool.

• Switch off the motor and pull the power plug before

you leave the workplace.

• Electrical installation work, repairs and mainte-

nance may only be carried out by persons who

have been specially trained.

• Ret all guards and safety devices immediately af-

ter you have completed any repairs or maintenance

work.

• Be sure to observe the safety information and op-

erating and maintenance instructions issued by the

manufacturer, as well as the dimensions listed in

the Technical Data.

• It is imperative to observe the accident prevention

regulations in force in your area as well as all other

generally recognized rules of safety.

• Note the information published by your profession-

al associations (VBG 7j).

• The saw is intended to be used indoors only.

• Workpieces that are smaller than the saw blade

guard can cause injuries to the hands or ngers.

Use suitable aids!

• Avoid cramped hand positions when guiding in the

workpiece and avoid positions in which slipping

could lead to your hand making direct contact with

the saw blade.

• Always t the saw blade with the teeth facing in the

direction of the sawing table.

• Always set the correct blade tension to prevent the

saw blades from jerking.

• Be especially careful when cutting material with ir-

regular cut proles.

• Exercise particular caution when cutting round ob-

jects such as rods and pipes. These can roll down

into the saw blade and cause the teeth to catch.

Use a wedge to brace such workpieces.

• The teeth can become caught in the kerf when

the workpiece is pulled back, especially if sawings

have lled in (blocked) the kerf. In this case, you

should switch the saw off, pull the power plug, clear

the kerf with a wedge, and remove the workpiece.

• Never leave the work area without having already

switched the saw off. Wait until the saw stops mov-

ing completely.

• Do not position, join, or construct any parts on the

work table while the saw is running.

• Only switch the saw on after you have removed any

remaining material and tools from the work table.

Leave only the workpiece to be machined and any

aids (e.g. wedges) on the work table.

• Always wear safety goggles!

• Keep your ngers at a safe distance from the saw

blade.

• Carefully guide the workpiece and keep it steady

at all times.

• Never leave the work area without having already

switched the saw off.

• Do not let your familiarity with the saw allow you

to be careless. Carelessness can lead to severe

injuries within a fraction of a second.

Safe work

• When transporting the electric tool, only use the

transport devices (Abb.1 Pos.10).

• Never use the protective devices for handling or

transport.

• Make sure that the lower part of the saw blade is

covered during transport, e.g. by the protective de-

vice.

• Working position is always laterally of the saw

blade.

Do not lose this safety information.

Warning! This electric tool generates an electromag-

netic eld during operation. This eld can impair ac-

tive or passive medical implants under certain condi-

tions. In order to prevent the risk of serious or deadly

injuries, we recommend that persons with medical

implants consult with their physician and the manu-

facturer of the medical implant prior to operating the

electric tool.

3. Layout (Figs. 1-12)

1 Blow-off device

2 Mounting

3 Knurled screw

4 Holder

5 Saw blade guard

6 Saw table

7 Cover, left

8 Bearings

9 Tightening lever

10 Arm

11 Graduated scale

12 Locking lever

13 Extractor connection

14 ON/OFF switch

15 Speed regulator

16 Assembly points

17 Sawblade

18 Retaining device

19 Upper adapter

20 Allen key, 3 mm

21 Angle (Not supplied)

22 Storage box for saw blades

23 Lower adapter

24 Saw blade holder, top

25 Saw blade holder, bottom

26 Table insert

27 Pointer

28 Screw

29 Bracket

30 Work lamp

31 ON / OFF switch work lamp

32 Setting gauge for saw blades without pin

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson DKS1600 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info