Bedienungsanleitung Toolson KGZ2550PRO (Seite 26 von 296) (Alle Sprachen)

782362

Zoom out

Zoom in

Vorherige Seite

1/296

Nächste Seite

26 GB

Attention! For bevel cuts (inclined saw head), the move-

able stop rail (28) must be xed in the outer position.

• Open the set screw (29) on the moveable stop rail

(28) and push the moveable stop rail (28) outwards.

• The moveable stop rail (28) must be locked in a po-

sition far enough from the inner position that the dis-

tance between the stop rail (28) and the saw blade (7)

is no more than 5 mm.

• Before making the cut, check that no collision could oc-

cur between the stop rail (28) and the saw blade (7).

• Tighten the set screw (29) again. (2x 8.6 + 8.7)

• Use the handle (13) to adjust the rotary table (16) to

the desired angle. The pointer (14) on the rotary table

(16) must match the desired angle on the scale (15)

on the xed saw table (17).

• Tilt the locking lever (13) back up again to x the rotary

table (16) in place.

• Cut as described under section 8.3.

8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1,2,6,8)

The crosscut saw can be used to make mitre cuts of 0°

- 45° in relation to the work face.

Important. To make miter cuts (inclined saw head), the

adjustable stop rail (28) must be xed at the outer po-

sition.

• Open the locking lever (29) for the adjustable stop

rail (28) and push the adjustable stop rail outwards.

• The adjustable stop rail (28) must be xed far enough

in front of the innermost position that the distance be-

tween the stop rail (28) and the saw blade (7) amounts

to a maximum of 5 mm.

• Before making a cut, check that the stop rail (28) and

the saw blade (7) cannot collide.

• Secure the locking lever (29) again.

• Move the machine head (5) to the top position.

• Fix the rotary table (16) in the 0° position.

• Loosen the set screw (22) and use the handle (1) to

angle the machine head (5) to the left, until the pointer

(20) indicates the desired angle measurement on the

scale (19).

• Re-tighten the xing screw (22).

• Cut as described in section 8.3.

8.7 Mitre cut 0°- 45° and turntable 0°- 45° (Fig. 1,2,6,9)

The crosscut saw can be used to make mitre cuts to

the left of 0°- 45° in relation to the work face and, at the

same time, 0° - 45° to the left or 0° - 45° to the right in

relation to the stop rail (double mitre cut).

Important. To make miter cuts (inclined saw head), the

adjustable stop rail (28) must be xed at the outer po-

sition.

• Open the locking lever (29) for the adjustable stop

rail (28) and push the adjustable stop rail outwards.

• The adjustable stop rail (28) must be xed far enough

in front of the innermost position that the distance be-

tween the stop rail (28) and the saw blade (7) amounts

to a maximum of 5 mm.

• Before making a cut, check that the stop rail (28) and

the saw blade (7) cannot collide.

• Secure the locking lever (29) again.

• Move the machine head (5) to its upper position.

• Release the rotary table (16) by loosening the set

screw (26).

• Using the handle (13), set the rotary table (16) to the

desired angle (refer also to point 8.4 in this regard).

• Re-tighten the set screw (26) in order to secure the

rotary table.

• Undo the locking screw (22) and use the handle (1)

to tilt the machine head (5) to the left until it coincides

with the required angle value (in this connection see

also section 8.6).

• Re-tighten the xing screw (22).

• Cut as described under section 8.3.

8.8 Limiting the cutting depth (Fig. 3)

• The cutting depth can be innitely adjusted using the

screw (26). To do this loosen the knurled nut on the

screw (26). Turn the screw (26) in or out to set the re-

quired cutting depth. Then re-tighten the knurled nut

on the screw (26).

• Check the setting by completing a test cut.

8.9 Sawdust bag (Fig. 2)

The saw is equipped with a debris bag (21) for sawdust

and chips.

Squeeze together the metal ring on the dust bag and at-

tach it to the outlet opening in the motor area.

The debris bag (21) can be emptied by means of a zip-

per at the bottom.

8.10 Changing the saw blade (Fig. 11-15)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Remove the spring (41) from the pin by pushing to-

gether the two ends.

• Release the guide bar (40) from the pin.

• Firmly press the saw shaft lock (4), and slowly turn the

ange screw (32) clockwise. After max. one turn, the

saw shaft lock (4) engages.

• Then undo the ange screw (32), by applying a slightly

greater force in a clockwise direction.

• Fully unscrew the ange screw (32) and remove the

outer ange (33).

• Press the unlocking lever (3) to slide back the saw blade

guard (6), then remove the saw blade (7) from the inner

ange (39) and pull out in a downwards direction.

• Carefully clean the ange screw (32), outer ange (33)

and inner ange (39).

• Insert the new saw blade (7) in the reverse sequence

and tighten.

• Position the guide bar (40) on the pin again, and se-

cure with the spring (41).

• Important! The cutting angle of the teeth, in other words

the direction of rotation of the saw blade (7) must coincide

with the direction of the arrow on the housing.

• Before continuing your work make sure that all safety

devices are in good working condition.

• Important! Every time that you change the saw blade

(7), check to see that it spins freely in the table insert

(11) in both perpendicular and 45° angle settings.

Toolson KGZ2550PRO Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info