Bedienungsanleitung Toolson KGZ2550PRO (Seite 27 von 296) (Alle Sprachen)

782362

Zoom out

Zoom in

Vorherige Seite

1/296

Nächste Seite

27GB

• Important! The work to change and align the saw

blade (7) must be carried out correctly.

8.11 Using the laser (Fig. 16,17)

• To switch on: Move the ON/OFF switch of the laser

(35) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact

guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(35) to the “0” position.

• Replacing the battery: Switch off the laser (34). Re-

move the battery compartment cover (37). Remove

the batteries and replace with new batteries (3 x

LR44) Check that the battery terminals are positioned

correctly when inserting new batteries. Close the bat-

tery compartment (36) again.

8.12 Changing the speed (Fig. 2)

The saw has 2 speed ranges:

langsam schnell

vitesse lente vitesse rapide

slow fast

Pomalu rychle

Pomalý rýchly

Počasnega hitrega

lassú gyors

бавно бързо

Nopea hidas

• To operate the saw at a speed of 3200 rpm (metal),

set the switch (42) to position I.

• To operate the saw at a speed of 4500 rpm (wood),

set the switch (42) to position II.

9. Transport (Fig. 1,2)

• Tighten the set screw (26) in order to lock the rotary

table (16)

• Activate the release lever (3), press the machine head

(5) downwards and secure with the safety pin (24).

The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw for

drag guide (23) in rear position.

• Carry the equipment by the xed saw table (17).

• When reassembling the equipment proceed as de-

scribed under section 7.1.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time

using a cloth. In order to extend the service life of the

tool, oil the rotary parts once monthly. Do not oil the

motor.

When cleaning the plastic do not use corrosive products.

Brush inspection

Check the carbon brushes after the rst 50 operating

hours with a new machine, or when new brushes have

been tted. After carrying out the rst check, repeat the

check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the spring

or contact wire are burned or damaged, it is necessary

to replace both brushes. If the brushes are found to be

usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

12. Electrical connection

The electrical motor installed is connected and ready

for operation. The connection complies with the ap-

plicable VDE and DIN provisions.

The customer‘s mains connection as well as the

extension cable used must also comply with these

regulations.

Important information

In the event of an overloading the motor will switch itself

off. After a cool-down period (time varies) the motor can

be switched back on again.

Damaged electrical connection cable

The insulation on electrical connection cables is often

damaged.

This may have the following causes:

• Passage points, where connection cables are passed

through windows or doors.

• Kinks where the connection cable has been improperly

fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the wall

outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insulation

damage.

Check the electrical connection cables for damage regu-

larly. Make sure that the connection cable does not hang

on the power network during the inspection.

Electrical connection cables must comply with the ap-

plicable VDE and DIN provisions. Only use connection

cables with the marking „H05VV-F“.

The printing of the type designation on the connection

cable is mandatory.

AC motor

• The mains voltage must be 230 V~

• Extension cables up to 25 m long must have a cross-

section of 1.5 mm2.

Connections and repairs of electrical equipment may

only be carried out by an electrician.

Please provide the following information in the event of

any enquiries:

Type of current for the motor

• Machine data - type plate

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolson KGZ2550PRO Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info