Bedienungsanleitung Trendnet TEW-712BR (Seite 28 von 51) (Englisch)

541687

Zoom out

Zoom in

Vorherige Seite

1/51

Nächste Seite

TRENDnet User’s Guide

TEW-712BR

disconnect power from the modem for approximately one minute, then reconnect the

power. For more details on this procedure, refer to your modem’s User Guide/Manual or

contact your ISP.

1. Log into your router management page (see “

Access your router management page”

on page 24).

2. Click on Main, and click on WAN.

3. Under your Internet connection settings, find the MAC Address section shown below.

4. Click either Clone MAC Address to clone the MAC address of the computer you are

currently using or manually enter the 12-digit MAC address of your old router.

5. To save changes, click Apply.

Change your router IP address

Main > LAN & DHCP Server

In most cases, you do not need to change your router IP address settings. Typically, the

router IP address settings only needs to be changed, if you plan to use another router in

your network with the same IP address settings, if you are connecting your router to an

existing network that is already using the IP address settings your router is using, or if

you are experiencing problems establishing VPN connections to your office network

through your router.

Note: If you are not encountering any issues or are not faced with one of the cases

described above or similar, it is recommended to keep your router IP address

settings as default.

Default Router IP Address: 192.168.10.1

Default Router Network: 192.168.10.0 / 255.255.255.0

1. Log into your router management page (see “

Access your router management page”

on page 24).

2. Click on Main, and click on LAN & DHCP Server.

3. Enter the router IP address settings.

• IP Address – Enter the new router IP address.

(e.g. 192.168.200.1)

• Subnet Mask – Enter the new router subnet mask.

(e.g. 255.255.255.0)

Note: The DHCP address range will change automatically to your new router IP

address settings so you do not have to change the DHCP address range manually to

match your new router IP address settings.

4. To save changes, click Apply.

Note: You will need to access your router management page using your new router

IP address to access the router management page. (e.g. Instead of using the default

http://192.168.10.1 using your new router IP address will use the following format

using your new router IP address http://(new.router.ipaddress.here)

to access your

router management page.

Set up the DHCP server on your router

Main > LAN & DHCP Server

Your router can be used as a DHCP (Dynamic Host Configuration Protocol) server to

automatically assign an IP address to each computer or device on your network. The

DHCP server is enabled by default on your router. If you already have a DHCP server on

your network, or if you do not want to use your router as a DHCP server, you can disable

this setting. It is recommended to leave this setting enabled.

1. Log into your router management page (see “

Access your router management page”

on page 24).

2. Click on Main, and click on LAN & DHCP Server.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trendnet TEW-712BR Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trendnet TEW-712BR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info