Bedienungsanleitung Trotec PAC3550PRO (Seite 13 von 19) (Englisch)

689434

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

EN 13

local air conditioner PAC 3550 PRO

Automatic defrost

At low ambient temperatures, ice may form at the evaporator.

The device will then carry out an automatic defrost.

The compressor switches off and the fan keeps running until

defrosting is completed. The duration of the defrost process can

vary.

Do not switch off the device during automatic defrost. Do not

remove the mains plug from the mains socket.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

• Switch off the device.

• Hold onto the mains plug while pulling the power cable out

of the mains socket.

• Empty the condensation tray if necessary.

• If necessary, remove the condensation drain hose and any

residual fluid from it.

• Clean the device according to the Maintenance chapter.

• Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

• Observe the operating temperature according to the

Technical data chapter.

• Check the filling level of the condensation tank, and empty

it if necessary. The FLindication (condensation tank full)

must not light up.

• Wait for 10minutes before restarting the device.

If the device is not starting, have the electrics checked by

a specialist company or by Trotec.

The device works with reduced or no cooling capacity:

• Check whether cooling mode is selected.

• Check the proper fit of the exhaust air hose. In case of

kinks, bends or blockage in the hose, exhaust air cannot

be discharged. Clear the way for the exhaust air.

• Check the position of the ventilation flaps. They should be

opened to the maximum.

• Check the proper fit of the supply air hose. In case of

kinks, bends or blockage in the hose, supply air cannot be

fed. Clear the way for the supply air.

• Check the air filter(s) for dirt. If necessary, clean or replace

the air filter(s).

• Check the minimum distance to walls or other objects.

Position the device a little more in the room's centre

if required.

• Check whether any windows and/or doors of the room are

open. If so, close them. One window has to remain open

for the exhaust air hose nonetheless.

• Check the temperature setting at the device. Reduce the

set temperature if it is higher than the room temperature.

The device is loud or vibrates:

• Check whether the device is set up in a stable and upright

position.

Condensate is leaking:

• Check the device for leaks.

The compressor does not start:

• Check whether the overheating protection of the

compressor has tripped. Disconnect the device from the

mains and let it cool down for approx. 10minutes before

reconnecting it.

• Check whether the ambient temperature equals the target

temperature (in cooling mode). The compressor will not

switch on unless the respective temperature is reached.

• The compressor may start up with a delay of 3min, as it is

provided with an internal protection against direct restart.

The device gets very warm, is loud or loses power:

• Check the air inlets and air filters for dirt. Remove external

dirt.

• From the outside, check the device for dirt (see chapter

Maintenance). If the inside of the device is dirty, have it

cleaned by a specialist company for cooling and

air-conditioning or by Trotec.

The device does not respond to the infrared remote control:

• Check whether the distance between remote control and

device is too large and reduce it if necessary.

• Make sure there are no obstacles, such as furniture or

walls, between the device and the remote control. Ensure

visual contact between device and remote control.

• Check the charging status of the batteries and change

them if required.

• If the batteries have only just been changed, check them

for correct polarity and change them if required.

Note

Wait for at least 3 minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to a specialist company for cooling and air-conditioning

or to Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PAC3550PRO Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PAC3550PRO

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info