Bedienungsanleitung Truma BGF 10 (Seite 9 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

631211

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Exhaust duct

Only the Truma AA 24 exhaust duct (part no. 39420-00) and

the ZR24 combustion air intake duct (part no. 39440-00) may

be used for the device , since the device has only been tested

and approved with these ducts.

Do not crush or kink ducts during installation.

Figure 3

Permissible duct lengths with wall cowl:

30 – 150 cm. Duct lengths of up to 50 cm can be laid with any

amount of upslope or with a downslope of max. 5 cm. To pre-

vent the ingress of water as much as possible, lay the ducts

(as shown in Figure 3) in a curve.

Connecting the exhaust double duct to the

device

– Push the clamp (7) over the ducts.

– Compress the exhaust duct (1) at its beginning so that the

coils are lying against each other.

– Slide the clamp (4) over the exhaust duct (1).

– Slide the exhaust duct (1) over the O-ring (2a) on the con-

nection (2) as far as the collar (3).

– Hook in the clamp (4) and screw it securely into place. Slide

the combustion air intake duct (5) onto the connection (6)

and secure with the clamp (7).

Figure 4

A new O-ring must be fitted whenever the exhaust duct

has been removed!

Selecting a location

The device must always be installed in such a way that it is

easy to access at all times for service work, and also easy to

remove and install.

Position the boiler in such a way that the cowl can be fitted to

an outer surface that is as straight and smooth as possible.

The wind must be able to flow around this outer surface at all

sides, and no decorative strips or panels should be present

there if possible, otherwise place the boiler on a suitable base.

The wall cowl must be attached such that there is no fuel tank

filler neck or fuel tank breather opening within 500mm (A).

There must also be no living area ventilation openings within

300 mm (A). If the cowl has been placed vertically beneath

an opening window, the boiler must be equipped with an au-

tomatic shut-off device in order to prevent operation with the

window open.

Window

Floor

300 mm

protected

area

protected

area

Figure 1

The boiler must not be installed close to or directly behind a

room heater.

In order to ensure that there is sufficient ventilation to cool

the electronics, the gap between the electronics cover (34)

and the walls of furniture items in which the boiler is installed

must be at least 20mm.

Installing the boiler

45º

20 mm

Figure 2

Set up the boiler on a suitable horizontal surface.

Attach the hose (2) to the 10 mm duct connection as far as

possible and fix it with a hose clamp (3). Lay the hose(2)

downwards or horizontally through the caravan floor to

drain directly to the outside. The hose must not be bent or

squeezed (use a hose guide if necessary).

Cut off the hose about 20 mm below the vehicle floor at a

45°angle relative to the direction of travel.

Securely screw the boiler to the retaining bracket (1).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma BGF 10 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Truma BGF 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info