Bedienungsanleitung Truma BGF 10 (Seite 10 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

631211

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Installing the wall cowl

Fit wall cowl to a surface that is as flat as possible so that air

can flow around at all sides.

– Drill opening (8) with a diameter of 70 mm (duct hole must

be lined with wood in cavities).

– Seal with provided rubber seal (10). Use flexible body seal-

ant on textured surfaces – do not use silicon.

– In the case of thicker walls, first connect the exhaust double

duct to the cowl from the outside.

– Slide rubber seal (10 – smooth side towards cowl, seal-

ing lips towards wall) and clamp (4) onto inner part of

cowl (11).

– Before pushing the exhaust double duct through the hole,

slide clamp (7) over duct.

70 mm

Figure 5

The ducts must be cut to length so that they protrude from

the hole for the cowl after installation. The exhaust duct (1)

must be 10 % longer than the combustion air intake duct (5).

This avoids exhaust duct expansion and tensile load.

– Compress the beginning of the exhaust duct (1) (approx.

2cm thereof) so that the coils are lying against each other.

– Push the exhaust duct (1) over the O-ring (2a) and onto the

connection (2) as far as the collar (3) (the wall cowl angle

faces upwards).

– Position the clamp (4) so that the flanged rim of the clamp

is gripping the collar.

– Screw the clamp (4) securely into place.

32a

Figure 6

– Secure the cowl inner part (11) with 3 screws (12) (pay at-

tention to the installation position – the Truma logo must be

at the bottom).

– Fit outer part of cowl (13) and screw it on with 2 screws (14).

– Slide combustion air intake duct (5) onto serrated connec-

tion (9) and secure with clamp (7).

A new O-ring (2a) must be fitted whenever the exhaust

pipe has been removed.

Water connection

Any pressure or immersion pump up to 2.8 bar can be used to

operate the boiler, as can any mixing battery with or without

an electric switch.

If connected to a central water supply (rural or urban con-

nection), or if more powerful pumps are being used, a pres-

sure reducer must be used, which will prevent pressures

higher than 2.8 bar from occurring in the system.

If using immersion pumps, a non-return valve (10–not in-

cluded in scope of delivery) must be installed between the

pump and the first branch (arrow indicates flow direction).

Figure 7

When pressure pumps with a large switching hysteresis are

being used, hot water may flow back via the cold water valve.

We recommend installing a non-return valve (11–not includ-

ed in scope of delivery) between the outlet to the cold water

tap and the drain valve as a return flow inhibitor.

Figure 8

In order to ensure that all the water is drained from the

boiler and that all water connections are leak-tight, the

water connections (12 + 13) and the drain valve (14) must

always be used.

Flexible hose installation

Truma can supply the water connections (12+13) and the

drain valve (14) with hose connection, diameter 10mm, as

accessories.

Pressure-resistant (up to 4.5bar), hot water-resistant (up to

+80 °C) , food-safe water hoses with an inner diameter of

10mm must be used.

Water hoses must be as short as possible and free of

kinks. All hose rubber connections must be secured

with hose clamps (including the cold water connection). The

warming of the water and its resulting expansion may gener-

ate pressures of up to 4.5bar in the drain valve (also occurs

with immersion pumps).

Route all water lines so they slope downwards to the

drain valve. Otherwise there is a risk of frost damage

that is not covered by the warranty!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma BGF 10 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Truma BGF 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info