Bedienungsanleitung Truma BGF 10 (Seite 11 von 44) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Schwedisch)

631211

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Cut off the venting hose about 20mm below the vehicle floor

at a 45° angle relative to the direction of travel.

45º

20 mm

Fig. 11 Flexible hose installation

45º

20 mm

Ø 12 mm

Fig. 12 Rigid pipe installation

(e.g. John Guest System)

Manufacture a hose connection (22) for the cold water supply

between the drain valve (14) and the elbow fitting (13– lower

tube) at the boiler.

Route hot water supply line (23) from elbow fitting with built-

in aeration valve (12–upper tube) to hot water consumption

points.

If a water supply is being installed in the vehicle, it must

be ensured that sufficient room is left between the water

hoses and the heat source (e.g. heater, warm air duct).

SC hose clips (part no. 40712-01) are suitable for fastening

the hoses to walls or the floor. These hose clips also make it

possible to route water hoses on the heater’s warm air distri-

bution pipes to prevent freezing.

A water hose may only be routed at a distance of 1.5 m from

the heater at the warm air duct. The Truma SC hose clip can

be used for distances greater than this. With parallel routing

(e.g. through a wall) a spacer (e.g. insulation) must be fitted in

order to avoid contact.

Rigid duct installation using the John Guest

system

Truma can supply the water connections (12+13) and the

drain valve (14) with a diameter of 12mm as accessories. In

this case it is advisable to always use John Guest pipes, inser-

tion sleeves and locking rings.

Suitable adapters (not included in scope of delivery) must be

used for connecting rigid pipelines with a different diameter.

Route all water lines so they slope downwards to the

drain valve. Otherwise there is a risk of frost damage

that is not covered by the warranty!

Installing the drain valve

Fit drain valve(14) in an easily accessible location in the vicin-

ity of the boiler. Drill hole with diameter of 18mm and insert

the drainage socket with hose(15). Secure the drain valve in

place with 2screws. Water removal can take place directly to

the outside in a splash-protected location (fit splash guards if

necessary).

Ø 18 mm

Figure 9

Water line routing

Connect cold water supply(16) to drain valve(14). The direc-

tion of flow is irrelevant.

Figure 10

Push elbow fitting without aeration valve(13) as far as poss-

ible onto the boiler’s cold water connection tube (lower tube),

and push the elbow fitting with built-in aeration valve(12) as

far as possible onto the boiler’s hot water connection tube

(upper tube). Pull in the opposite direction to check that the

elbow fittings are securely attached.

Slide venting hose with an outer diameter of11mm (20) onto

the hose nozzle of the aeration valve (21) and route to the out-

side free of kinks. Radius of arc must not be less than 40 mm.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma BGF 10 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Truma BGF 10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info