Bedienungsanleitung Truma Mover Mover TE R4 (Seite 17 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch)

484649

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

To prevent the battery from becoming totally discharged dur-

ing long periods of inactivity it must be disconnected and re-

charged before using again. Charge the caravan battery

before starting up.

It is extremely easy for you or your caravan dealer to perform

the checking and maintenance of your Mover® during the

annual inspection of your caravan. If in doubt, please contact

the Truma Services (see Truma Service Booklet or

www.truma.com).

Checks

Check the installation, wiring and connections for damage

at regular intervals. The drive units must be able to move

freely and be returned automatically to the safe idle position

when they are disengaged. If this is not the case, examine

drive units for soiling or corrosion at the guides and clean

if necessary. Undo all moving parts as required and oil or

spray with a lubricant such as WD40 to ensure that the

equipment moves correctly and provides the full range of

movement.

After the annual inspection, check whether all motors react

properly to the buttons on the remote control.

At least every 2 years, an expert must check the Mover®

for rust, check that detachable parts are firmly attached and

check that all safety-related parts are in good working order.

Emergency disengaging function

If the caravan battery has become so discharged that a disen-

gaging cannot be performed using electrical means, or a fault

has occurred, the drive motors can be disengaged manually.

Prise out the plastic cap (m) at the

rear end of the motor using a screw-

driver. Place the socket wrench

(size 7 mm – included in scope of

delivery) onto the hexagon bolt and

disengage the drive unit by turning

anticlockwise. Repeat the process

for all drive units.

Once the battery has been recharged the rollers can be

engaged again electrically.

Trouble-shooting

Check that the batteries in the remote handset are in

immaculate condition!

Check whether the caravan plug has been plugged into the

safety socket!

Check whether the caravan battery is in immaculate condition

and is fully charged! Please note that battery performance can

deteriorate considerably at cold ambient temperatures.

Check if the flat fuses (20 A) for the engagement motors are

OK. If the fuses are faulty, check for a short circuit in the con-

nection cables of the engagement motors, which are con-

nected to the control systems!

Perform a reset (approx. 10 seconds – briefly disconnect

battery or disconnect and reconnect safety plug)! Check again

that all the drive units are in the correct position.

If this does not solve the problem, please contact the Truma

Service.

–

Synchronising the electronic control unit with

the radio remote hand set

Remote control and control system (master) are synchro-

nised to each other ex works.

If the control unit or the remote hand set is replaced, they

must be re-synchronised as described below.

Check that the assembly has been carried out as specified

in the installation instructions and that the drive rollers have

no contact. Check that the battery is properly connected,

check the condition of the battery and that a voltage of 12 V

is present at the control unit. Please ensure that the caravan

plug has been plugged into the safety socket.

Press the reset button (k) on the control unit and hold down

(red LED – j – flashes slowly), and after approx. 5 seconds the

LED (j) starts to flash rapidly. Then release the reset button

and press and hold down the caravan reverse button on the

remote hand set (c) within 10 seconds, simultaneously switch-

ing on the remote hand set using the slide switch (a).

MASTER

The remote hand set and the control unit are synchronised to

each other. After successful synchronisation, the red LED

flashes rapidly.

Technical data

Operational voltage

12 V DC

Current consumption

average approx. 65 A maximum 150 A

Stand by consumption

< 2 mA

Remote hand set frequency

Class 1, 868 MHz

Speed

approx. 17 cm per second (depending on weight and incline)

Weight

approx. 66 kg

Fuse engagement motors

Blade fuse 20 A

Fuse in positive supply cable

150 A

Area of operation Mover® TE R4

Dual axle caravans with a total weight up to 3000 kg

Right to effect technical modifications reserved!

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Truma Mover Mover TE R4 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info